Assume that a 16x2 LCD is connected to the 8051 microcontroller. Write an assembly 8051 program that displays a signed numbers every one second on this display(only one number at each moment) 127,126, ..., 3, 2, 1, 0, -1, -2, ...,-127, -128, 127, ...

Assume that a 16x2 LCD is connected to the 8051 microcontroller. Write an assembly 8051 program that displays a signed numbers every one second on this display(only one number at each moment) 127,126, ..., 3, 2, 1, 0, -1, -2, ...,-127, -128, 127, ...

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter7: Input/output Technology

Section: Chapter Questions

Problem 24VE

See similar textbooks

Related questions

Q: Briefly explain the two basic approaches used to minimize register-memory opera- tions on RISC…

A: - : Two basic approaches used to minimize register-memory operations on RISC machines : - Two…

Q: 5) 8086 computer system using 24MHZ crystal oscillator, the duration of the bus cycle of system is-…

A: Lets see the solution in the next steps

Q: } The memory space of an 8085A based microcomputer consists of one 8K*8 bit EPROM starting from the…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: Consider a processor that contains eight 16-bit registers. Design a complete Register file and…

A: Answer

Q: Parallel electrical conducting lines are used to link the various components that are found on the…

A: Introduction: In this question, we are asked to write the name of those lines that are parallel…

Q: Consider the following situation: In an 8088-based microprocessor, it is needed to interface with 6…

A: Lets see the solution.

Q: Draw the 8259 microcontroller Internal block diagram. And explain how it works.

A: In the below can i explain block diagram of 8259 with description of each component in the 8259…

Q: An 8-bit data is read from an input device and stored in the memory location Ox20000200. This data…

A: Assembly instructions: MOV This instruction copies the source operand value to destination register.…

Q: e differences

A: EEPROM (also called E2PROM) stands for electrically erasable programmable read-just memory and is a…

Q: Given the assembly code: org 8000h ld a,5 loop: dec a jp p, loop halt Explain what each line does.…

A: An assembly code is provided to be discussed. The code uses the instruction sets of the Z80…

Q: The following is a RISC mini-SPARC instruction given in HEX: A8 23 60 D1 a) To what family of…

A: Answer: Our guideline is answer the first three subparts form the first part. Given A8 23 60 D1

Q: Choose the correct RISC-V instructions that can be used to jump to the instruction at PC = Ox0000…

A: This problem is from RISC-V instructions.Let’s see some points about RISC-V instructions.

Q: Every rotation of a motor causes a switch to be pushed. The switch, like most mechanical switches,…

A: SOLUTION

Q: suppose you’re trying to interface a matrix keyboard connected to a seven segment display, to…

Q: Q2 Construct a 32 K x 16 RAM chip using • 4 chips 8K x 8 4 chips 4K x 16 1. Show the decoding…

A: We have to find out how many chips required to design or construct a 32Kx16 RAM chip using 2…

Q: Given a machine-code RISC-V instruction is divided as in the figure below, choose the possible…

A: According to the information given:- We have to choose the correct option to satisfy the mentioned…

Q: Discuss the difference between SDR and DDR DRAM.

A: Answer:- The most significant difference between DDR and SDR is that DDR reads data on both the…

Q: In the 8086 computer system using 15MHZ crystal oscillator, The time required to writing a word to…

A: Answer: I have given answer in the brief explanation.

Q: (20%) Some RISC-V assembly instructions are shown below. Assume that the variables f,g are assigned…

A: check further steps for the answer :

Q: For a multiplexer based bus system in an 8 bit computer system with 4 registers: a- What is the MUX…

A: NOTE: As per Barlteby guideline, if there multiple part then we are allowed to solve only first…

Q: Answer the following Questions: QI. In most RISC-V systems, the most commonly used instruction is…

A: Note: As per company guidelines we are supposed to answer only first Part please repost other Parts…

Q: A, B are two integers arrays. The base address of A and B are in register x10 and x11, respectively.…

A: Let's see the solution in the next steps

Q: An 8-bit data is read from an input device and stored in the memory location 0x20000200. This data…

A: Assembly instructions: MOV This instruction copies the source operand value to destination register.…

Q: Is the CMPS instruction confusing in any way?

A: Introduction: Two strings are compared using the CMPS instruction. The DS: SI and ES: DI registers…

Q: Assume that a 16x2 LCD is connected to the 8051 microcontroller. Write an assembly 8051 program that…

A: Attached Handwritten Solution:

Q: rt pseudocode given below into Assembly code. int A[]={4, 8, 12, 16, 20, 24, 28} int sum=0 for(…

A: int main(){ int A[] = {4, 8, 12, 16, 20, 24, 28}; int sum = 0; for(int i = 0; i < 7;…

Q: pared to RISC machines

A: RISC: Reduce the cycles per instruction at the cost of the number of instructions per program.…

Q: Computer Fundamentals In the instruction ADD A, B, the answer gets stored in ___________ A B B A C…

A: Here The Instruction says ADD A,B means Add B to A and Store it To A.

Q: Develop an Intel 8086 ALP using BIOS interrupts to print a 100x50 (in pixels) parallelogram in cyan…

A: Intel 8086 is a sixteen-bit HMOS microprocessor. It is to be had in forty pin DIP chip. It uses a 5V…

Q: Translate the following C code into RISC V (32-bit) assembly instructions,

A: C program: C is a programming language developed by Dennis Ritchie at AT &T Bell Laboratory in…

Q: Assume that a RISC processor executes each instruction in 2 microseconds and that an /O device can…

A: Given, RISC processor takes two microseconds(0.002 milli sec) to execute each instruction. I/O…

Q: 3. Suppose that Two -7-segment displays is connected to PORTB and PORTA of a microcontroller…

Q: Design an interface between 8086 CPU and two chips of 16K X 8 EPROM a

A: solution in below step

Q: We suppose that the 8051 is connected to 8 LEDs through the port P₁. The LEDs are common cathode and…

A: The commands that you simply see within the code area unit in hexadecimal type and area unit…

Q: TRUE OR FALSE The size of a single instruction of RISC-V 64-bit ISA is 64-bits. The size…

A: 1) True

Q: In the 8086 computer system using 15MHZ crystal oscillator, The time required to writing a word to…

A: Each timer needs a clock to work. In earlier processors the main source of clock used to be an…

Q: 1. The segment addresses are assigned as 0000H to FO00H and the offset addresses values are from…

A: As per guidelines, I'm supposed to answer first question, therefore i answered 2 questions. Re-post…

Q: Every rotation of a motor causes a switch to be pushed. The switch, like most mechanical switches,…

A: the answer is given below:-

Q: Assume IM -300 picoseconds, TALU 150 picoseconds. TAdder 150 picoseconds,TReg 50 picoseconds Add Ax,…

A: Execution:

Q: Give the basic pipeline of a RISC processor. Assuming that each phase can have 4 parallel…

A: Pipelining: Pipelining is a process of arrangement of hardware elements of the CPU such that its…

Q: Write a Nios II assembly program using the CPULATOR SIMULATOR that reads binary data from the Slider…

A: Algorithm:; read binary data from the Slider Switches, SW11-0, on the DE2-115 Simulator; The binary…

Q: ification of a digital co

A: Instruction Set Architecture" is the specification of a digital computer's hardware implementation.…

Q: Every rotation of a motor causes a switch to be pushed. The switch, like most mechanical switches,…

A: Switch Bounce When a mechanical switch or relay closes, the switch elements will often bounce, even…

Q: Among the following which statements are not TRUE? A small part of the area of a wafer contains the…

A: Wafer is the slice of semiconductor in which Integrated chips can be fabricated. Wafers are…

Q: translate c code in risc-v 32 bit assembly instructions, then convert to machine code(hex) variables…

A: Here below we write risc-v 32 bit assembly instructions, code to show that: a=b+c-64…

Q: Write the RISC-V assembly code that creates the 64-bit constant 2222111144443333(16) and stores that…

A: lui - Load Upper Immediate that is the upper 16 bits. addi - Perform the addition on the source…

Q: The interrupt vector for INT 06 is located at the physical address

A: Physical Address calculation: Step1: Interrupt Address * 4 Step 2: Convert the result of Interrupt…

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

Assume that a 16x2 LCD is connected to the 8051 microcontroller. Write an assembly 8051 program that displays a signed numbers every one second on this display(only one number at each moment)

127,126, ..., 3, 2, 1, 0, -1, -2, ...,-127, -128, 127, ...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “AB9876543CDEF210” should display on 7-seg Display and when user press 2 leds should glow 17 times in a loop. If any other key is pressed no action should be taken Rubrics: Analytic Approach (50%) Syntax (25%) Desired output (25%)
Find the machine code for the following instruction in RISC-V. Assume all instructions are labeled sequentially, for example, I1, I2, I3, …, I200. I10 : BGE x10, x20, I100
Consider a raster display system with resolution of 800 by 400. How many pixels could be accessed per second by a display controller that refreshes the screen at the rate of 60 frames per second?
A RISC processor has 186 total registers, with 18 globals. There are 12 register windows, each with 10 locals. How many input/output registers are in each register window?
Give the basic pipeline of a RISC processor. Assuming that each phase can have 4 parallel executions, how many time units are required for twenty instructions? Give the instruction by instruction working
Connect a 5*7 dot-matrix display to the 8051-microcontroller (Draw the schematic on paper and upload it as a photo). Then, display the content of variable NUMBER on the display, digit by digit every one second. for example if NUMBER=249, then "2" will be displayed for one second, after that digit "4" and finally digit "9" will be displayed for a whole second. Assume that the necessary lookup table exists in Memory at address 0xF000
Consider two raster system with the resolution 640 * 480 and 1280 * 1024. How many pixels could be accessed per second in each of these systems by a display controller that refreshes the screen at a rate of 120 frames per second? What is the access time per pixel in each system?
Consider a 32-bit machine where four-level paging scheme is used. If the hit ratio to TLB is 98%, and it takes 20 nanosecond to search the TLB and 100 nanoseconds to access the main memory what is effective memory access time in nanoseconds?
A RISC instruction pipeline has five stages with propagation delays of 20 ns, 25 ns, 20ns, 70 ns, and 40 ns, respectively. What is the clock period? If a non-pipelined CPU can process an instruction in 160 ns, what is the actual steady-state speedup of the pipeline?
Assume that a RISC processor executes each instruction in 2 microseconds and that a 1/O device can only wait for an interrupt to be serviced for 1 millisecond before it is serviced. The number of instructions that may be executed when interruptions are deactivated is restricted.
Flagonly in RISC-V (RVS) answer the following both question, thumps up if both Write an instruction that subtracts 1245 (in decimal) from x20 and stores the result in x22. Write an instruction that multiplies the signed integer in x14 by 4096 (in decimal) and stores the result in x18.
Choose an answer and write the procedureIn a microcontroller, the interior of the memory that goes from 0x200 to 0x21FF has been reserved for the program code.What is the maximum size that a program code can have?A) 256B) 512C) 1024D)128