At a given instant the slider block A is moving to the right with the motion shown. Suppose that r = 3 m and 1-3 m. (Figure 1) Figure 1 of 1 30° V₁ = 4 m/s aA=6m/s² Determine the angular acceleration of link AB measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. αAB = Submit Π ΑΣΦ vec My Answers Give Up Part B Determine the magnitude of the acceleration of point B at this instant. rad/s²

At a given instant the slider block A is moving to the right with the motion shown. Suppose that r = 3 m and 1-3 m. (Figure 1) Figure 1 of 1 30° V₁ = 4 m/s aA=6m/s² Determine the angular acceleration of link AB measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. αAB = Submit Π ΑΣΦ vec My Answers Give Up Part B Determine the magnitude of the acceleration of point B at this instant. rad/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The smooth bar AB shown rotates in the horizontal plane about point A at the constant rate of 77 rpm. At the instant shown, the 9.4 kg collar C is at r=AC=6.8 m, and it is sliding outward relative to the bar at a speed of 11 m/s. For this instant, the following is required (i) Draw the free body diagram of collar C (ii) Write down the radial and transverse components of the acceleration of the collar C (iii) Write down the equations of motion for collar C (iv) Determine the magnitude of the force(s) exerted by bar AB on the collar
Consider that at the instant shown, bar AB of the mechanical system below has a angular velocity (wAB) counterclockwise at 5 rad/s and an angular acceleration (alphaAB)counterclockwise 2 rad/s².The length of bar AB is 0.4 m and the length of bar BC is 1 m. For the instant shown, and using a "Analysis of Relative Motion", determine: (a) the speed of point B (b) angular velocity of connecting bar BC (c) the speed of point C (d) the acceleration of point B (d) the acceleration of point C
The bucket of a backhoe is the element AB of the four-bar linkage system ABCD. Assume that the points A and D are fixed and that the bucket rotates with a constant angular velocity WAB = 0.25 rad/s. In addition, suppose that, at the instant shown, point B is aligned vertically with point A, and C is aligned horizontally with B. Determine the acceleration of point C at the instant shown along with the angular acceleration of the elements BC and CD. Let h= 0.66 ft, e= 0-46 ft, l= 0.9 ft, and w= 1.0 ft.
In a continuous printing process, paper is drawn into the presses at a constant speed v. Denoting by r the radius of the paper roll at any given time and by b the thickness of the paper, derive an expression for the angular acceleration of the paper roll.
A 500 mm. diameter hoop rolls without sliding down the 30-degree inclined rough surface. At the instant shown, the speed of point B is 2.72 m/s. Which of the following best describes the speed of point D? Choices: 2.72 m/s, 1.923 m/s, 5.44 m/s, 1.360 m/s
A disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0 rad/s, the angular acceleration α=2.0 rad/s2. The radius of the disc is r=1.0 m. Determine e) the magnitude of the acceleration of the point A, aA= ___________m/s2
An airplane flying at a constant speed of 240 m/s makes a banked horizontal turn. What is the minimum allowable radius of the turn if the structural specifications require that the acceleration of the airplane shall never exceed 4 g?
It is known that the static frictional force between block B and the plate will be overcome and the block will slide when its acceleration reaches 3 m / s2 (Figure 7b_4). If the plate starts from rest at t = 0 s and accelerates uniformly at a rate of 4 rad / s2 , determine the time t and the angular speed of the plate when the block starts to slip (r = 200 mm).
Hi, I need help with this question please. Block A is connected to a fixed pin O with a string 100 mm long. The block and the channel are at rest when a motor on a shaft through O starts to rotate the channel with angular velocity ω = sin(0.2t) rad/s and the string starts to pull the block towards O with speed v = sin(0.2t) mm/s. 1. At the time instant t = 2.5π s, determine: a) the components of the velocity and acceleration of the ball in polar coordinatesb) the speed of the ballc) the components of the velocity and acceleration of the ball in normal coordinatesd) sketch the polar and normal components of the velocity and acceleration of the ball on the figure.
The disk with radius r = 0.2 m (figure below) starts from rest and receives an angular acceleration at clockwise given by alfa= (3t3)rad/s2, where t is given in second. That said, for t = 3 s determine: (a) the angular velocity of the disk (b) the velocity intensity of a point P on the edge of the disk. Represent the direction of the velocity vector at point P indicated in the figure (c) the intensities of the normal and tangential components of the acceleration of a point P in the edge of the disc. Plot the direction of these acceleration components at the indicated point P in the figure
During the start of a light aircraft engine, one of its propellers rotates 120 revolutions in 4 seconds before reaching constant operating speed. Assuming that the propeller accelerates uniformly during start, determine the acceleration during start and the angular velocity. operational.
Pulley B is being driven by the motorized pulley A that is rotating at ωA =20 rad/s. At time t = 0, the current in the motor is cut off, and friction in the bearings causes the pulleys to coast to a stop. The angular acceleration of A during the deceleration is αA = −2.5t rad/s2, where t is in seconds. Assuming that the drive belt does not slip on the pulleys, determine (1) the angular velocity of B as a function of time; (2) the angular displacement of B during the period of coasting; and (3) the acceleration of point C on the straight portion of the belt as a function of time.Note: R1 as your last three numbers of your university ID, and R2 is half of that. Units in mm