At a point in a stressed material, the major principal stress is 50 kPa compression and the minor principal stress is 20 kPa compression. Use Equations 1 and 2 to determine the maximum shear stress that acts through the point and the normal stress on the plane of this maximum shear.

At a point in a stressed material, the major principal stress is 50 kPa compression and the minor principal stress is 20 kPa compression. Use Equations 1 and 2 to determine the maximum shear stress that acts through the point and the normal stress on the plane of this maximum shear.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Related questions

Q: If the stresses on two perpendicular planes through a point are 60 N/mm2 tension, 40 N/mm2…

A: Given that, σ1 = 60 N/mm2 σ2 = -40 N/mm2 τxy=30 N/mm2 The inclination of the plane with the axis of…

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 90 MPa and S, =…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: A cylindrical shaft of 75mm diameter is subjected to a maximum bending moment of 2500 Nm and a…

Q: Using the equations for determination of stress at a point, calculate the value for the maximum…

Q: At a point in a stressed material, the major principal stress is 80 psi compression and the minor…

A: (a) The major principal stress is σ1 is 80 psi (compression) The minor principal stress σ3 is 20 psi…

Q: 3. Consider the given state of stress 40MPA y +, 10MPA → 70MPA 22.5° a) Determine the principal…

A: As per the bartleby guidelines, i am able to answer three sub-parts at a time so I was answered the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 60 MPa and Sy =…

Q: At a point in a stressed material, the major principal stress is 120 kPa compression and the minor…

Q: The stresses shown act at a point in a stressed body. Assume stress magnitudes of Sx = 18 MPa, S, =…

Q: In a two dimensional stress system, the two principal stresses are a, of is 240 N/mm² and Poisson's…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 90 MPa and S, =…

A: Given data in question Normal stresses Angle To find out Normal stress and shear stress

Q: if the normal stress in x direction is 14 Ksi and the normal stress in the y direction is 9 Ksi and…

A: Given data : Normal stress in X direction σX=14 ksi Normal stress in Y direction σY=9 ksi Minimum…

Q: At a point on the free surface of a stressed body, a normal stress magnitude of S, = 69 MPa (C) and…

A: To find unknown stresses on the horizontal and vertical plane

Q: 1. At a point, the normal and shear stresses acting on one plane are 120 psi compression and 30 psi…

Q: The major and minor principal stresses acting at a point in a stressed material are 80 psi…

A: Major Principal stress, σ1=-80 psi (compression) Minor Principal stress, σ2=20 psi (Tension) (a)-…

Q: At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 52 MP exist on…

A: To find unknown stresses

Q: At a point in a stressed material, the major principal stress is 7.2 ksi compression and the minor…

A: It is required to determine the maximum shear stress. We know that, the maximum shear stress acts at…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and…

A: Given Sx=60Mpa Sy=-215Mpa

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and S, =…

A: Given data in question Normal stress on element Angle To find out Normal and shear stresses

Q: At a point on the free surface of a stressed body, a normal stress magnitude of Sy-74 MPa (T) and an…

A: σ1=185 Mpaσ1-σ22=83 Mpaσ1-σ2=166σ2=186-σ1=186-185σ2=1 Mpa

Q: The major principal stress and deviator stress at a point are 100 kPa and 60 kPa, respectively.…

A: Calculate minor stress and angle of inclination between the given plane and the major principal…

Q: At a point, the normal and shear stresses acting on one plane are 8,000 psf compression and 2,000…

A: Given: Compression of normal stress at point = 8000 psf Compression of shear stress at point = 2000…

Q: gas under pressure of 2.2 MPa. a. b. Determine the value of the tangential stress in the tank wall…

Q: At a point in a stressed material, the major principal stress is 44 kPa tension and the minor…

A: Given data:

Q: A thin-walled long cylindrical tank of inside radius r is subjected simultaneously to internal gas…

Q: A stepped circular shaft fixed at one end is subjected to two axial forces as shown below. The…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 85 MPa and S, -…

Q: At a point in a stressed material, the major principal stress is 180 kPa compression and the minor…

A: Given :σx = -180 Kpa σy =…

Q: Show complete solution, include necessary figures. The major and minor principal stresses acting at…

A: Major and minor principal stress are given and it has been asked to find Mohr circle maximum shear…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 100 MPa and Sy…

Q: At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor…

A: (a) The diagram for the Mohr’s circle stress combination is shown below.

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin of an airplane.…

A: A,B and C are arrangement of rosette (Delta rosette)εB = εn at θ = 0°εA = εn at θ = 60°εC = εn at…

Q: Direct tensile stresses of 120 MN/m and 70 MN/m' act (at a point) in a body on mutually…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S,, - 95 MPa and S,…

Q: Determine maximum shear stress and maximum principal stress

A: Given data : The value of normal stress in X direction σX=80 MPa The value of normal stress in Y…

Q: For the state of stress at a given point M shown below. Determine Р 1. The normal stress and shear…

Q: For the given state of stress, determine (a) the principal planes, (b) the principal stresses, (c)…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: At a point in a stressed material, the stress combination acting on a plane is a 90 kPa compressive…

A: (a) The Mohr's circle for the stress combination is shown below. The radius of the circle from the…

Q: A bar of cross-section 850 mm² is acted upon by axial tensile forces of 60 kN applied at each end of…

A: Given, Cross section area = 850mm² Tensile force = 60kN Let the direction of loading axis is x

Q: 1. Determine the effective stress at point A when Z-3 m. 2. Determine the effective stress at point…

Q: Using the maximum shear stress (MNST) and maximum normal stress theory (MSST) , find the minimum…

A: According to maximum shear stress theory: ζmax≤0.5σy Where, ζmax = Maximum shear stress σy= Yield…

Q: At a point on the free surface of a stressed body, a normal stress magnitude of S, = 63 MPa (C) and…

A: To find unknown stresses in horizontal and vertical plane

Q: If the principal stresses in a plane stress problem, are oj = 100 MPa, 02 = 40 MPa, the magnitude of…

A: Given: σ1= 100MPa, σ2= 40MPa Calculate: Max. shear stress=?

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a point in a stressed material, the major principal stress is 7.2 ksi compression and the minor principal stress is 3.6 ksi compression. Using Equations 1 and 2, determine the maximum shear stress that acts at the point and the normal stress that acts on the plane of the maximum shear stress.
The major and minor principal stresses acting at a point in a stressed material are 80 psi compression and 20 psi tension. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stresses acting on a plane that is 30° ccw from the major principal plane.
At a point in a stressed material, the major principal stress is 44 kPa tension and the minor principal stress is 18 kPa tension. Using Equations 1 and 2, determine the maximum shear stress that acts through the point and the normal stress on the plane of maximum shear.
At a point in a stressed material, the major principal stress is 180 kPa compression and the minor principal stress is 40 kPa tension. (a) Determine the Mohr’s circle for this stress combination. (b) What is the maximum shear stress that acts at the point, and what is the value for the normal stress acting on the plane of maximum shear? (c) Determine the value of the normal and shear stress acting on the plane 22.5° ccw from the major principal plane.
At a point in a stressed material, the major principal stress is 66 kPa compression and the minor principal stress is 34 kPa tension. (a) Use the Mohr’s circle to determine the shear and normal stress on a plane 45° ccw from the major principal plane. (b) Determine the stress combination acting on the plane 75° ccw from the major principal plane.
At a point in a stressed material, the stress combination acting on a plane is a 90 kPa compressive stress and a 30 kPa shear stress, while on a perpendicular plane, the stress combination is 30 kPa compression and 30 kPa shear. Use the Mohr’s circle for this stress analysis. (a) Determine the values of the major and minor principal stresses. (b) Determine the angle between the major principal plane and the plane where the 90 kPa compressive stress acts.
The major principal stress and deviator stress at a point are 100 kPa and 60 kPa, respectively. Indicate the magnitude of the minor principal stress. What is the value of the maximum shear stress and of the normal stress acting on the same plane? (Deviator stress is the algebraic difference between the values for the principal stresses.)
At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor principal stress is 2,000 psf compression. (a) Draw the Mohr’s circle for this stress combination. (b) Find the maximum shear stress, and also indicate the value of normal stress acting on this same plane. (c) Determine the values of the normal and shear stresses acting on a plane that is 60° ccw from the major principal plane.
At a point in a stressed material, the major principal stress is 80 psi compression and the minor principal stress is 20 psi compression. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on this same plane? (c) Determine the value of the normal and shear stress acting on a plane that is 60° clockwise (cw) from the minor principal plane.
Determine the maximal normal stress and max shear stress
At a point, the normal and shear stresses acting on one plane are 8,000 psf compression and 2,000 psf, respectively. On a perpendicular plane, the normal and shear stresses are 2,000 psf compression and 2,000 psf, respectively. (a) Draw the Mohr’s circle. (b) Determine the value of the principal stresses. (c) Find the angle between the plane on which the 8,000 psi compressive stress acts and the major principal plane. (d) What is the maximum shear stress acting at the point?
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.