Answered: At standstill condition, the back emf…

At standstill condition, the back emf is zero, so the motor can be safely turned ON without a starter. Select one: OTrue O False

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter34: Motor Installation

Section: Chapter Questions

Problem 3PA: Refer to the first Practical Application in this set. When the 50-HP motor replaces the 30-HP motor,...

See similar textbooks

Related questions

Q: In the simple lamp dimmer shown here, what method of power control is being used? LAmP AC supply…

A: The figure shows a lamp dimmer circuit, this circuit uses the DIAC and TRIAC combination for the…

Q: Q3/ Why is a starting resistor used in de motor circuits? Explain 3 point starter

A: Consider that the resistors in the dc motor are used to reduce the current at the starting of the DC…

Q: Which of the following is a safety device in a motor control circuit. Select one: a. selector switch…

A: In the motor control circuit , motor contactor is used to switch the current at the time of…

Q: (i) Using circuit diagram and the current-time characteristics, explain the motor overload…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: What is a starte

A: A motor is an electromechanical device which is used to convert the electrical power into mechanical…

Q: Three - wire control prevent the restarting of machinery when power is restored.

Q: For switching OFF the motor normally open push butt Select one: O True False

A: The explanation is as follows.

Q: At standstill condition, the back emf is zero, so the motor can be safely turned ON without a…

Q: If generator armature current is 2A, the motor armature current is 3A, Voltage is 240V,motor…

A: Generator current Ig = 2A Motor current Im = 3A Voltage V=240V Motor Armature resistance Ra= 4 ohm…

Q: Using the following control devices ,draw an electrical circuit that will manage the direction of…

A: Given circuit-

Q: 11. Write down a program with the procedures to rotate a motor in both directions.

A: We need to write the program with the procedures to rotate in both directions.

Q: Q2 ) I. What is the effect of changing the sequence of phases in the electric feeder (single phase,…

A: According to Bartleby guidelines we are supposed to answer only one question of they are not…

Q: If an electrical defect occurs in the electronic powersteering(EPS) system, __ .a. the system…

A: EPS (Electronic Power Steering):- A crucial piece of technology for fully autonomous driving is…

Q: How can you reduce the amount of voltage applied to the motor during inching?

Q: Explain the effect of the generated emf of a d.c. motor and why a d.c motor starter is necessary.

A: Electrical machines are distinguished on the basis of their supply. There are AC machines for AC…

Q: An electrician inspects an electric motor that doesn't run properly. What is wrong with this motor?

A: In this question we need to inspects an electric motor that doesn't run properly. What is wrong with…

Q: Identify the dc motor used for Elevator with a neat sketch explain its working

A: According to question we have to explain type of dc motor use for Elevator.

Q: What is three point starter ? What is four point starter? What is the nessecity of starter...!

A: Three point starter : In the three-point starter, the NVC is located in series with the sector…

Q: Explain how does the current will be reduced during the starting of the motor.

A: According to question we have to explain, how does the current will be reduced during the starting…

Q: Screen. 2 € Which one of the following motors has high starting torque?

A: DC SERIES MOTOR: In a DC series motor the value of torque is directly proportional to the armature…

Q: If both the forward and reverse contactors for a motor engage at the same time, what will happen to…

A: In this question we need to discuss what happen when both the forward and reverse contactors for a…

Q: the blocked rotor test is performed on a wound rotor motor and if the rotor winding is kept open,…

A: Always remember , the current flows through a close path. When the rotor winding are open i.e., no…

Q: Investigate the faulty motor shown below to determine why doesn't the motor work?

A: A DC motor is a Electric device which converts the electrical energy into physical motion. The…

Q: A DC shunt motor is connected to a three-point starter. What would happen if (i) the starter handle…

A: (i) The armature current of the DC machine is meant to grow slowly as the machine slowly builds…

Q: Technician A says when testing the voltage output, if the charging voltage is too high, the cause…

A: Technician A is right because testing of the output voltage is too high, the cause could be open…

Q: Explain the effect of the generated emf of a d.c. motor and why a d.c motor starter is necessary.

Q: Using the following control devices draw an electrical circuit that will manage the direction of…

A: In the case of DC motor, the Direction of rotation can be reversed by either reversing the polarity…

Q: A 75 hp Induction-typed Squirrel cage motor, 575 volts rated two-phase motor. Calculate its phase…

Q: Develop a relay ladder diagram for the sequence control of two motor starters using a single…

A: To develop relay ladder using nema symbols

Q: Electrical machine What is the speed of 100kW, 230-volt, three-phase, four-pole, 60Hz…

Q: 4. Explain the need, salient features and working with the help of a neat circuit diagram showing…

A: as per the guidelines, we supposed to answer one question at a time so please ask other questions…

Q: 19. You’re powering up a new motor in a brushless motor control system. After moving the shaft of…

A: It is being given that : after moving the shaft of the motor slightly left to right, the motor…

Q: Large motor should be connected directly across the line on start up

A: To explain that whether large motor should be connected directly across the line on start up.

Q: The starter must never operate for more than sixty seconds at a time and should rest for two minutes…

A: The starter must never operate for more than sixty seconds at a time and should rest for two minutes…

Q: The motor will work when the wire loop is connected to the [select all that apply) split ring…

A: The commutator changes direction of current at a point where direction is zero. This keeps the…

Q: Using the following control devices draw an electrical circuit that will manage the direction of…

Q: Determine the no. of studs and resistance of the section for a D.C. series motor starter from data:…

Q: Can I use the Manual Motor Starter on a single phase motor? Why?

A: MANUAL MOTOR STARTER Manual motor starters are devices that use manual or automatic switches to…

Q: Differentiate the sizes of manual starters

Q: |The nameplate rating of a motor is 150 hp, 600 volts, 205 A, 1700 rpm. The resistance of the shunt…

Q: Direct current is used in which of the following applications in the industry?

Q: QV Answer the following questions for the 3-ph induction motor connection below, A/ What is the…

Q: overload heater element

A: If an overload heater element is not installed in a two-pole manual starter then the Motor will not…

Q: List 3 hazards when constructing (working) with a homemade D.C motor and how it can be managed?

A: List of some hazards when constructing (working) with a homemade D.C motor: Do not use in a…

Q: what advantage is there in using combination starters?

A: The advantages of using combination starters are given below: The starter can be operated in the…

Q: 1. Give detail explanation on why it is necessary to use d.c. motor starters for starting of d.c.…

A: DC motor - DC machine is not used in the present time. Day by day reduces uses in industrial purpose…

Q: 17. When starting winding, normal locked rotor current? a motor draws approximately what percentage…

A: In this question we will write motor current when starting on one winding..

Question

At standstill condition, the back emf is zero, so the motor can be safely turned ON without a starter. Select one: OTrue O False

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

At standstill condition, the back emf is zero, so the motor can be safely turned ON without a starter. Select one: O True O False?
3. Explain the difference between manual motor starters that provide low voltage release and those that do not.
Select the best answer for each of the following. The purpose of overload protection on a motor is to protect the a. motor from sustained overcurrents. b. wire from high currents. c. motor from sustained overvoltage. d. motor from short circuits.
A starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct?
Why are stranded copper wire is used instead of solid copper wirename the four types of battery capacity rating What type of engine conversion occurs when the battery is discharging? List the seven components of the starting system List the four most common start a customer complaints What is the name of the stationary coil that produces current in the AC generator? what is the name of the company that creates the rotating mechanical field of the AC generator?
10 kW, 400 volt 3 phase star connected synchronous motor has negligible armature resistance the synchronous reactance per phages 10 ohms. Determine the minimum current that the motor will draw if the excitation is varied. The full load efficiency of motor is 80% 10 minute fast please answer
A 460VAC rated, 60 Hz, 125-Hp Three-phase induction type motor is to be connected for across-the-line starting. The nameplate indicates the motor’s maximum ampere rating, 160A. It has a NEMA code letter B. The ambient temp of the installation place is and TW copper will be used. Short-circuit protection device that will be used is Inverse Time Breaker. Calculate the Motor Starter Size.
1/ What is the purpose of resistor which is connected with starting electrode? 2/How does an electronic starter work? 3/ In the testing & Inspection the color must be verified, why?
Using the following control devices ,draw an electrical circuit that will manage the direction of rotation of the DC motor. With the pushbutton in its normal state, the motor should be rotating in one direction. Actuating the pushbutton should reverse the motor’s direction of rotation.
Determine the minimum current for conductors required to connect a motor that has a full-load current of 46 A.
A belt-driven 202 Hp shunt wound DC generator is running at 465 rpm and issupplying full load to a bus bar at 232 V. At what speed will it run if the belt breaksand the machine continue to run taking 9 kW from the bus bar? The armature andthe field resistances are 0.05 Ohm and 100 Ohms respectively. The brush contactdrop is 2 Volts per brush.
Investigate the faulty motor shown below to determine why doesn't the motor work?