At the instant shown, the uniform slender rod with mass m = 32 kg is pin-supported at point O. It has dimensions a = 0.24 m and b = 0.70 m. Determine its mass moment of inertia l, (in kg•m²) about the axis that passes point O and is perpendicular to the screen. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. M Your Answer: Answer

At the instant shown, the uniform slender rod with mass m = 32 kg is pin-supported at point O. It has dimensions a = 0.24 m and b = 0.70 m. Determine its mass moment of inertia l, (in kg•m²) about the axis that passes point O and is perpendicular to the screen. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. M Your Answer: Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.26P: The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If...

See similar textbooks

Similar questions

A cord 3.0 m long is coiled around the axle of a wheel. The cord is pulled with a constant force of 40 N. When the cord leaves the axle, the wheel is rotating at 2.0 rev/s. Determine the moment of inertia of the wheel and axle. Neglect friction.
A cylinder shown has a weight of 100lb Assuming the cylinder to be solid indetermining the moment of inertiaa.Determine the velocity of the cylinder after it has rolled 10ft from restif the horizontal force P applied at A is 10lbb.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at Bc.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at C
A cylinder shown has a weight of 100lb Assuming the cylinder to be solid indetermining the moment of inertiaa.Determine the velocity of the cylinder after it has rolled 10ft from restif the horizontal force P applied at A is 10lbb.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at Bc.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at
5kg plate, and 3 kg slender rod. FIND, the radius of gyration of the pendulum about an axis perpendicular to the screen and passing through the point G.
Determine the rotational inertia of the device shown below. R = 0.50 m, r = 0.2 m, the mass of the box is 30 kg. When Fapp= 176 N, the box has an upward acceleration of 0.8 m/s2. Use g = 9.8 N/kg.
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If the drum begins rotating slowly counterclockwise, determine how far the plank will travel before it comes to rest again. (Note: Because the drum rotates slowly, the inertia of the plank may be neglected.)
The rigid body of the figure rotates freely around the pivot in A. If the body is released from the rest in the displayed position, determine: a) What is the moment of inertia of the body around the axis of rotation in A? b) Where is the center of mass located? Provide a drawing with the dimensions. c) Perform the respective analysis and complete the following table It can be assumed that the body consists of two equal thin rods with a mass of 5 kg and an L length of 1.3 m each. Please attach the free body diagram if necessary
Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
A) Determine the position of the center of gravity of the figure's structure. B)Determine the moment of inertia of mass with respect to the x' axis that passes through the structure's center of gravity and is parallel to the x axis. The cone has a density of 600 kg/m3 and the cylinder a density of 800 kg/m3. Consider H = 83
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)