At the nodes in the truss system given in the figure occurring displacement and the stress and reaction that occurs Find the forces.E=200Gpa A=10000mm2

Q: Q 2: The homogeneous wire ADOBC is bent into a semicircular arc and two straight section as shown.…

A: The single load acting on the point A is given as,F=20 N The force couple is acting on the point B…

Q: 4. The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN…

A: a.Shear stress in rivet:ss=PAs=50×1000π4×20×20×3=53 MPa

Q: A 30 kN weight is supported by means of a pulley as shown in the figure. The pulley is supported by…

A: Load = 30 kN Allowable stress in tension = 140,000 KN/m2 Allowable stress in compression = 96,000…

Q: Find the Tensions TCA and TCB for the system as shown in figure. Take R = 100 mm, S= 240 mm e = 70°,…

A: Given system with strings 'CA' and 'CB' is shown below. Here, φ=tan-1RS=tan-1100240=22.62°…

Q: AB, BC, BD ropes made of material with elasticity value in Table 2 are in balance as shown in the…

A: Given Data: θ=90° β=120° α=150° FAB=40000 N Areas: AAB=200 mm2 ABC=173 mm2 ABD=100 mm2 Lengths:…

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

A:

Q: 1. A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter…

A: Note - As per our company guidelines we are allowed to answer only the first three subparts. kindly…

Q: Determine the reactions at A and B and the load Q required to hold bar AB in a horizontal position…

A:

Q: The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate…

A: ∑Md=0 1.25EFcosα + 1.25EFsinα = 0 EF=0 BY equating the sum of forces in x-direction and y-direction…

Q: The homogeneous rod of constant cross section is attached to unyielding supports. The rod carries an…

A: Now,  Taking in consideration all Horizontal forces  ∑FH = 0R1 + R2 = P R2 = P -R1   .. .. . . . . .…

Q: At the nodes in the truss system given in the figure occurring displacement and the stress and…

A:

Q: Two steel ropes connected to each other at point C are loaded as shown in the figure. The maximum…

A:

Q: 3-22. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: 3-22 Given, The diameter of the strut AB, ds=12 mm=0.012 m The diameter of the post CD, dp=40…

Q: Ifthe gap between Cand the rigid wall at D is initially 0.13 mm as shown in Figure 1 and the…

A: Here, l1 = 650 mmd1 = 50 mmA1 = π4 d12 = 1963.5 mm2l2 = 610 mmd2 = 25 mmA2 = π4d22 = 490.9 mm2E =…

Q: the member is subjected to a distributed load and a point force as shown in the figure. Determine…

A:

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Take moment about the point E = 0

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A:

Q: Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads…

A: Given: The diameter of circular bent rod, d = 20 mm

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Given data :-  At A = 6 KN  At E = 8 KN   Find :-  The force in Member AE = ?

Q: 1. The cable and boom shown in the figure support a load of 600 lb. Determine the tensile force T in…

A:

Q: Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: To assemble the truss (axial rigidity EA of the three bars) in Figure 3 the end point P of bar 2 has…

A: The change in length of the member 2 if the force acting in member 2 is F2,

Q: 2. From the system shown in the figure, obtain the forces and the average axial stress on each bar…

A:

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A:

Q: The uniform 300-Ib bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…

A:

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A:

Q: 6. Determine the largest weight W that can be supported safely by the structure shown in the figure.…

A: Given:σAB=16,000 psiσBC=760 psiAAB=0.5 in2ABC=16 in2

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN is…

A: Welding joints are used to join two different materials together. There are different types of…

Q: The lap joint is connected by three 10-mm-diameter rivets. Assuming that the axial load P = 100 kN…

A:

Q: A- ODD: A 2.0 kN bar AB carries a load F = 75 kN vertical force at A. The bar is supported by a pin…

A:

Q: Q.4) Determine the tensions in the three cables supporting a weight of 180 N as shown in figure…

A: Let us take origin as O. FBD:   From figure, O = (0,0,0) A = (4,-8,5) B = (-6,-8,5) C = (0,8,5)…

Q: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a…

A:

Q: To assemble the truss (axial rigidity EA of the three bars) in Figure 3 the end point P of bar 2 has…

A:

Q: The bank in the figure is considered to be a person sitting and the force exerted on the board is…

A: Consider an inbuilt beam as shown below.

Q: 9 Determine reactions in A and tension in cable as shown in figure? 300 KN 30 kN/m 20 kN/m mm Xal 2m…

A:

Q: Q.2. The beam EF given in figure weighs 10 N/cm and carries the 138 N weight at its end. It is…

A: The free-body diagram of the beam EF is given as, The vector BA is written as, The unit vector in…

Q: The uniform 300-lb bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…

A:

Q: Determine the largest weight of the picture frame that can be by the two ropes Tas shown in the…

A:

Q: What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant…

A:

Q: From the figure, the load at G is 12 kN: To determine: a) Piston force JL b) Pin force E and M c)…

A: Draw FBD of GEM and calculate pin forces at E and M:

Q: In the system in the figure, two rods carry the P force. a) Since the maximum stress that the rods…

A:

Q: Construct the reduced stiffness matrix of the shown truss, Fig. 3.Then determine the nodal…

A:

Q: A– EVEN: A 1.5kN bar AB carries a load F = 65 kN 4m vertical force at A. The bar is supported by a…

A:

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: The three A992 steel bars shown in the figure are attached to a rigid member. If the applied load on…

A:

Q: 9. The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the…

A: An object is considered to be in a condition of equilibrium when all of the forces acting on it are…

Q: The uniform 300-1b bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.