The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in th hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d =8.75 in., e = 1.95 in., and f = 1.95 in. W e D a]

The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in th hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d =8.75 in., e = 1.95 in., and f = 1.95 in. W e D a]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.4.11P: 2.4-11 Three steel cables jointly support a load of 12 kips (see figure). The diameter of the middle...

See similar textbooks

Similar questions

A plane truss has a pin support at F and a roller support at D (see figure). (a) Find reactions at both supports (b) Find the axial force in truss member FE.
A plane Frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin connected at B. A triangularly distributed lateral load with peak intensity of SO N/m acts on CD. An inclined concentrated force of 200 N acts at the mid-span of BC. (a) Find reactions at supports A and D. (b) Find resultant forces in the pins at B and C.
A soccer goal is subjected to gravity loads (in the - z direction, w = 73 N/m for DG, BG, and BC; w = 29 N/m for all other members; see figure) and a force F = 200 N applied eccentrically at the mid-height of member DG. Find reactions at sup ports C, D, and H.
A space truss has three-dimensional pin supports at joints 0, B, and C, Load P is applied at joint A and acts toward point Q. Coordinates of all joints arc given in feet (see figure). (a) Find reaction force components B x, B z, and Oz (b) Find the axial force in truss member AC.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
Consider the plane truss with a pin support at joint 3 and a crtica1 roller support at joint 5 (see figure). (a) Find reactions at support joints 3 and 5. (b) Find axial forces in truss members 11 and 13.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
A plane frame has a pin support at A and roller supports at C and E (see figure). Frame segments A BD and CDEF are joined just left of joint 1) by a pin connection. (a) Find reactions at supports A. C. and E. (b) Find the resultant force in the pin just left of D.
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.