Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 17.4 ksi for steel, 9.9 ksi for aluminum, and 16 ksi for bronze. Bronze Aluminum Steel A= 0.62 in? A=0.93 in? A=0.47in? 2P 3P 4P P 10 ft 16 ft 13 ft

Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 17.4 ksi for steel, 9.9 ksi for aluminum, and 16 ksi for bronze. Bronze Aluminum Steel A= 0.62 in? A=0.93 in? A=0.47in? 2P 3P 4P P 10 ft 16 ft 13 ft

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Could you help with the reaction forces? Dy, Ay, Ax, Dx ? thanks
Given that the Gerber beam is drawn. Calculate and draw SFD,BMD,NFD Note : 1 ton = 1000kg Solve max in 25-30 mintes thank u
Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will support a 110kN and the ultimateshearing stress for the steel used is 360MPaand that a factor of safety of 3.35 is desired,determine the increase in the bolt diameterrequired if an additional 100kN load is addedto the existing 110kN.
Continuing the solution of the given problem, find the required tie wire in kilograms if the reinforcements are space at: a.Vertical bars spaced at 80 cm and one horizontal bars atevery 3 layers of the block. b.Vertical bars at 60 cm and one horizontal bar at every after2 layers of the block. c.Tie wire in kilograms. (30 cm) Attached are the previous solutions
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
A rectangular beam with notches and a hole (seefigure) has dimensions h = 5.5 in., h1 = 5 in., and widthb =1.6 in. The beam is subjected to a bending momentM =130 kip-in., and the maximum allowable bendingstress in the material (steel) is σmax = 42,000 psi.(a) What is the smallest radius Rmin that should beused in the notches?(b) What is the diameter dmax of the largest hole thatshould be drilled at the midheight of the beam?
Dont round off initial value, round off final answ only
Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 145 psi. Determine the smallest allowable length L (in inches rounded to the nearest hundredths) that can be used for the splice plates for an applied load of P = 14,000 lb. Note that a gap of a = 0.6 in. is required between boards (1) and (2).
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to another plate by 34 mm diameter bolts as shown in the figure. Assume diameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steel plate with yield strength Fy = 248 MPa and minimum tensile strength Fu = 400 MPa. For a chain holes extending across a part in any diagonal or zigzag line, the net width of the part shall be obtained by deducting from the gross width the sum of the diameters or slot dimensions of all holes in the chain and adding, for each gage space in the chain, the quantity S24g where S is the longitudinal center to center (pitch) of any consecutive holes, in millimetres and g is the transverse center to center spacing (gage) between fastener gage lines in millimetres. If a = 60 mm, c = 150 mm and d = 100 mm. Determine the nearest value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Determine the nearest value…
The cast iron block with cross-sectional dimensions of 62.5 mm by 62.55 mm consists of two pieces. The pieces are prevented from sliding along the 55 deg inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron bearing and 345 MPa for the key in shear. If the block is loaded with P=287 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.