The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses , in the steel and wood, respectively. If the moduli of elasticity are E (s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) %3D Steel 50 mm 50 kN/m Wood Steel 50 mm 4.0 m 150 mm 250 mm

The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses , in the steel and wood, respectively. If the moduli of elasticity are E (s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) %3D Steel 50 mm 50 kN/m Wood Steel 50 mm 4.0 m 150 mm 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. a. What is the moment of inertia (in mm4) of the cross-section of the beam? b. What is the value of Q (in mm3)? c. What is the actual bending stress of the beam in MPa? d. What is the actual shearing stress of the beam in MPa?
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Consider a wood beam (see figure) carrying a uniform load of 16.5 kN/m (which includes the weight of the beam). The length is 1.55 m and the cross section is rectangular with width 150 mm and height 300 mm. * Inserted Photo* If the beam is simply supported as in figure part (a), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ? MPa ?max= ? MPa (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ?MPa ?max= ? MPa
Calculate the maximum shear stress tmax the maximum bending stress emax in a wood beam (see figure) carrying a uniform load of 22.5 kN/m (which includes the weight of the beam) if the length is 1.95 m and the cross-section is rectangular with a width of 150 mm and height 300 mm, and the beam is either (a) simply supported as in the figure part a, the or b has sliding support at right as in the figure part b.
A cantilever beam is of length 1.5 m, loaded by a concentrated force P at its tip as shown in figure, and is of circular cross section (R = 100 mm), having two symmetrically placed longitudinal holes as indicated. The material is titanium alloy, having an allowable working stress in bending of 600 MPa. Determine the maximum allowable value of the vertical force P.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
Figure 1a shows a simply supported beam, AB of length L = 3 m, with a uniform distributed load of w = 4.8 kN/m. The bending moment diagram is shown below the beam and the cross-section in Figure 1b. The cross section has a constant thickness t = 9.4 mm, the width of the flange is b = 253.8 mm and height of the web is d = 206.8 mm. Determine the maximum bending stress in compression. Determine the maximum bending stress in tension
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa