b 3 ft 1 ft

Q: F 500lbs 30° 240lbs

A:

Q: (b) the height of he building

A: For solution refer below images.

Q: Find the height of the tower using the information given in the illustration. 85.624° 60 ft The…

A: Given data,  Distance of Base of the tower is given  b= 60 ft.  Angle θ= 85.624°  Let h be the…

Q: F2 Find the x-component of F2 in Newtons. If the calculated answer is not whole number, express it…

A:

Q: 0. Given the shaded area shown below, determine

A:

Q: C 3 ft

A: Writing the co-ordinates of different points – The position vector

Q: The height (in m)

A: Given data; A ball of mass 0.1 kg, initially at rest Ball dropped from height of 1 m.Ball impact…

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: Use your weight in pounds (while standing on the surface of the Earth) to calculate your mass in the…

A: Given that  1 kg weighs approx. 2.205 lb on the surface of the Earth

Q: 30 B 45° 30° D

A: Part A) Draw the free body diagram at point B. Similarly, draw the FBD at Point D.

Q: Aheat pump with the COP of 2.1 supplies heat at the rate of 135 kJ/min. If a bar heater was used and…

A: Given:COP=2.1Qs=135 KJ/minCp=R2.50/KWhCo=200 cents off-peak

Q: Convert 80 psig to its absolute pressure in psi where atmospheric pressure is 99 kPa.

A:

Q: given 9 cm %3D Ege =0.2

A: given:diameter d=9cmQ=0.2m3/sθ=1000

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Distance between two stations A and B, actual length = 100 km Equivalent distance on map, length…

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: H.w-1 Find the area of the shapes in the figure and then find the center of gravity? Choose this Or…

A: As per the company's guidelines when multiple questions are asked only first question has to be…

Q: New plastic fuel tanks for cars can be molded to many shapes, an advantage over the current metal…

A: As there are 2 questions so we are solving  question 1 If you want the 2nd question or the question…

Q: b -y = x³ a

A: Given: y =x3 a =1.9m, b =6.859m   Iy =∫X2*dA take a small area element dA at distance x from y-axis…

Q: 4. If 6.5 m³ of oil weighs 46,800 N, calculate its density in kg/m³. (a) 285 (b) 258 (c) 82 (d) 734

A: Given : volume of oil , V = 6.5 m3             weight of oil , W = 46800 N To find : density

Q: show the angle of declination by drawing the figure and write the important results by making the…

A: (a) Defiition: Angle of declination: It is defined as the angle between magnetic axis and…

Q: 9 in. D 8 in. 12 in. W = 720 lb

A:

Q: Each element of a circular corical pile of sand 6 ft. high is indined 40° to the horizontal. How…

A: Given data,  h= 6 ft  Inclination = 40° for the cone  Material to be filled is sand.

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Given dataDistance between two stations D = 100KmLenght on the drawing sheet = 2.5cmMaximum length L…

Q: Represent the following as a number between 0.1 and 1000 using an appropriate prefix:0.00563 mg.

A: Given: The given number is N=0.00563 mg. The conversion factor to convert the given unit in the…

Q: Q2: Draw the orthographic Projections of given object. 30 80

A: The orthographic projection with 1st angle projection is shown in the step below.

Q: В 100 m

A:

Q: A tank contains 500 kg of a liquid whose specific gravity is 2. Determine the volume of the liquid…

A: Given: m=500 Kg S=2

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Find the x-component of F1 in Newtons. Find the y-component of F1 in Newtons. Find the z-component…

A: The data given is, F1=400 N ϕ=41° θ=36°

Q: building has the dimensions of 20 feet by 49 feet.   What is the area of the building in square…

A: Given dimension of the building Length = 49 ft Breadth = 20ft    To determine :the area of building…

Q: Please solve this question carefully and circle the final answer with the correct units use the…

A: Given that ,  D=30 mm E =73.1GPa Triangular distributed axial load .

Q: lote: Use three decimal places and no need to input the unit. Figure the 20°C water and gasoline are…

A: This problem is the application of the pascal's law, which states that the the pressure at a point…

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: F -L/2 -L/2 k

A: The total deflection of a beam under load F is equal to compression due to spring and elastic…

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: B-Determine the value of shaded area of the following figure.

A:

Q: How many balls of 50 mm diameter fit in a volume of 4.1 m^3

A:

Q: A 3 meter-high room is heated through a vertical steam pipe. If the bulk temperature of steam in the…

A:

Q: 1. Determine the reading on the vernier scale as indicated by the arrows.

A: According to scale Main scale reading = 41 mm Least count = 1/20= 0.05 mm Vernier scale = 5*0.05=…

Q: A constant density bar with mass m and ler in place as shown. Use the usual x,y,z oo the following…

A:

Q: 1. Draw the given plane figure, and dimension the drawing.

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.