B, 600 mm 150 E mm D 300 700 mm mm It is proposed to turn a hand pump into a motorized pump by attaching its lever to a motorized crank-lever system, as shown. With the water pump lever velocity of vɛ = 1.2 m/s, upward, and with the crank angular position, 0 = 31.2345°, clockwise, find the frequency (rpm) of the motor (in terms of angular velocity of link AB) needed in the system. %3D USING PURELY RMA METHOD. Note: Points A and D are on the same level. %3D

B, 600 mm 150 E mm D 300 700 mm mm It is proposed to turn a hand pump into a motorized pump by attaching its lever to a motorized crank-lever system, as shown. With the water pump lever velocity of vɛ = 1.2 m/s, upward, and with the crank angular position, 0 = 31.2345°, clockwise, find the frequency (rpm) of the motor (in terms of angular velocity of link AB) needed in the system. %3D USING PURELY RMA METHOD. Note: Points A and D are on the same level. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axial flow pump produces a discharge of 0.095 m3/sm3/s. (Figure 1) The impeller is rotating at ω� = 80 rad/srad/s, and it has a mean radius of 75 mmmm. The diameter of the impeller's shaft is 100 mmmm. Determine the angle α2�2, which the velocity of the water as it exits the blades V2�2 makes with its tangential component Vt2��2. Express your answer using three significant figures.
Consider an inward flow reaction turbine in which velocity of flow at inlet is 3.8m/s. The 1m diameter wheel rotates at 240rpm and absolute velocity makes an angle of 16° with wheel tangent. Determine (1) velocity of whirl at inlet, (2) absolute velocity of water at inlet, (3) vane angle at inlet, and (4) relative velocity of water at entrance. Show the schematic diagram and complete solution with units.
A two stage centrifugal pump is designed to discharge water at a total head of 70 m with an overallefficiency of 0.76. The pump runs at 2331.6 rpm. The actual head developed (per stage) is 65% ofthe theoretical head. The flow at the inlet is pure radial. The impeller at the exit has a diameter of D2=0.219m and a width b2=0.0216m .The outlet blade angle is ?= 28°. Determine:1. The flow rate of the pump.2. The output power of the two stage centrifugal pump. Take ρ= 1000kg/m^3g=9.81 m^2/s
A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radialat the inlet of the rotor. The pump has the following characteristics:Flow rate Q = 72 L/sInlet diameter D1 = 90 mmOutlet diameter D2 = 280 mmHead H = 25mWidth at the inlet b1 =20 mmWidth at the outlet b2 = 18 mmLeakage q = 2 L/sMechanical loss Pm = 1.41 kWBlade angle at the outlet β2 = 35ͦThe water density ?=998 ??/m^3Atmospheric pressure 101 kPa1) Draw the velocity triangles at the inlet and the exit of the impeller.2) Determine the magnitude of the absolute velocity of the flow (?) and the impeller velocity(U) at the inlet and outlet3) Determine the blade angle at the inlet.4) Determine the hydraulic, mechanical and volumetric efficiencies.5) Determine the minimum number of blades required for the slip to not exceed 0.9.6) Determine the static pressure difference (P2-P1) through the impeller by using Bernoulliequation.7) Determine the available NPSH if the pump is placed 2m above the…
A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radialat the inlet of the rotor. The pump has the following characteristics:Flow rate Q = 72 L/sInlet diameter D1 = 90 mmOutlet diameter D2 = 280 mmHead H = 25mWidth at the inlet b1 =20 mmWidth at the outlet b2 = 18 mmLeakage q = 2 L/sMechanical loss Pm = 1.41 kWBlade angle at the outlet β2 = 35ͦThe water density ?=998 ??/m^3Atmospheric pressure 101 kPa1) Draw the velocity triangles at the inlet and the exit of the impeller.2) Determine the magnitude of the absolute velocity of the flow (?) and the impeller velocity(U) at the inlet and outlet3) Determine the blade angle at the inlet.4) Determine the hydraulic, mechanical and volumetric efficiencies.5) Determine the minimum number of blades required for the slip to not exceed 0.9.6) Determine the static pressure difference (P2-P1) through the impeller by using Bernoulliequation.7) Determine the available NPSH if the pump is placed 2m above the…
The length and diameter of a suction pipe of a single-acting reciprocating pump are 5m and 10 cm respectively. The pump has a plunger of diameter 15cm and a stroke length of 35 cm. The center of the pump is 3 m above the water surface in the pump. The atmospheric pressure head is 10.3 m of water and pump is running at 3r rpm. Determine: a. Pressure head due to acceleration at the beginning of the suction stroke, b. maximum pressure head due to acceleration and c. pressure head in the cylinder at the beginning and at the end of the stroke
1 The internal and external diameters of the impeller of a centrifugal pump are 200 mm and 400 mm respectively. The pump is running at 1200 rpm. Forward blades make an angle of 150o at exit and at inlet the angle is 20o. The blade thicknesses at the inlet and outlet are 100mm and 70mm respectively. The hydraulic efficiency of the pump is 87%. Assume the water enters the impeller radially. i Draw neatly the outlet velocity diagram and the inlet velocity diagram. ii Find the Euler power of the pump. iii Find the net Head of the pump. Ans: (ii)140.65W; (iii) 43.42m
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. (a)At what speed, in RPM, should the turbine run under a head of 11 meters? (b)What horsepower would be developed?
a. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. b. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocityis 25 ft./s. The wicket gates are turned at an angle such that relative velocity at theinlet flow makes an angle of -45° with the blade velocity. The wheel and hub radiiare 3.6 ft. and 1.6 ft., respectively. The turbine rotates at 240 rpm. If water leaves theblade in a purely axial direction, calculate H and all relevant angles.Ans: H=81.87 ft.; α1=31.8°; β2=20.93°
A pump is designed to deliver 9500 L/min of water at a required head of 8 m. The pump shaft rotates at 1100 rpm. The pump specific speed in nondimensional form is (a) 0.277 (b) 0.515 (c) 1.17 (d ) 1.42 (e) 1.88