B) A 120-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm= (1.5 + j 20) 12 and auxiliary winding, Za = (10 + j 5) Q . Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.

B) A 120-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm= (1.5 + j 20) 12 and auxiliary winding, Za = (10 + j 5) Q . Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

Name three factors that determine the torque produced by an induction motor.
A 110-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm (1.2 +j 25) ohm and auxiliary winding, Z,= (12+j 5) ohm. Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.
A four-pole, single-phase, 120 V, 60 Hz induction motor gave the following standstill impedances when tested at rated frequency:Main winding : Zm =1.5+j4 ohmsAuxiliary winding : Za =3+j6 ohmsa) Determine the value of external resistance to be inserted in series with the auxiliary winding to obtain maximum starting torque as a resistor split-phase motor.b) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque as a capacitor-start motor.c) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque per ampere of the starting current as a capacitor-start motor.d) Compare the starting torques and starting currents in parts (a), (b), and (c) expressed as per unit of the starting torque without any external element in the auxiliary circuit, when operated at 120V, 60Hz.
A 25 HP, 6 pole, 50 Hz, 3-phase slip ring induction motor runs at 960revolutions per minute on full load with a rotor current per phase of 35 A.Allowing 250 W for the copper loss in the short-circuiting gear, and 1000Wfor mechanical losses, find the resistance per phase of the three-phaserotor winding.
A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtainmaximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in theauxiliary winding circuit when operated from a 120V, 60Hz supply
A 220 V, single-phase induction motor gave the following test results:Blocked-rotor test: 120 V, 9.6 A, 460 WNo-load test: 220 V, 4.6 A, 125 WThe stator winding resistance is 1.5 Ω, and during the blocked-rotor test, the starting winding is open. Determine the equivalent circuit parameters. Also, find the core, friction and windage losses.
1.Show that if three phase currents, each of equal magnitude and differing in phase by 120degree, flow in a three phase winding that are 120 degree apart from each other then it willproduce a rotating magnetic field of a fixed magnitude. 2. A three phase, 5-hp, 60Hz, 115V, 4-pole induction motor is operating at rated voltage, rated frequency, and 125 percent rated load has an efficiency of 85.4 percent. The stator conductor loss, rotor copper loss and core loss are 223.2W, 153W, and 114.8W respectively.Sketch the power flow diagram, enter the given data, and determine i) shaft speed ii) shaft torque 3. Can single phase induction motor be self-started? Explain the operation of a split phase single phase induction motor?
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
18. A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtain maximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in the auxiliary winding circuit when operated from a 120V, 60Hz supply.
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
A three-phase, two-pole, 35 hp, 480 V, 60 Hz, Y-connected induction motor has the following constants in ohms per phase referred to the stator: Rl = 0.322Ω R2 = 0.196 Ω X1 = 0.675Ω X2 = 0.510Ω Xm = 12.5Ω The total rotational losses are 1850 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 3% at the rated voltage and rated frequency, determine the following: (a) The speed in rpm and in rad/s (b) The stator current (c) The power factor (d) The developed power and output power (e) The developed torque and output torque (f) The efficiency.
A 200V, 3, star connected induction motor takes 30A at a line voltage of 35V with rotor locked. With this line voltage, power input to motor is 450W and core loss is 60W.The dc resistance between a pair of stator terminals is 0.15Ω. If the ratio of ac to dc resistance is 1.6, find the equivalent leakage reactance/phase of the motor and the stator and rotor resistance per phase.