B) A force of 460 N is exerted on lever AB, as shown in fig. (4). End B is connected to a piston into which fits a cylinder having a diameter of 60 mm. What force Fp acts on the larger piston, if the volume between C and D is filied with water? 460 N 260 mm 220 mm 120mm 60 mm

B) A force of 460 N is exerted on lever AB, as shown in fig. (4). End B is connected to a piston into which fits a cylinder having a diameter of 60 mm. What force Fp acts on the larger piston, if the volume between C and D is filied with water? 460 N 260 mm 220 mm 120mm 60 mm

Name: B) A force of 460 N is exerted on lever AB, as shown in fig. (4). End
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: B) A force of 460 N is exerted on lever AB, as shown in fig. (4). End B is connected to a piston into which fitsa cylinder having a diameter of 60 mm. What force Fp acts on the larger piston, if the volume between C and Dis filied with water?460 N22

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.
A force of 460 N is exerted on level AB as shown. The end B is connected to a piston which fits into a cylinder having a diameter of 60 mm. What force Fd acts on the larger piston, if the volume between C and D is filled with water?
4. At what depth below the surface of the oil, relative density 0.85 will produce a pressure of 120 kN/m? What depth of water is this equivalent to? A. Depth of oil in meters? B. Depth of water is this equivalent to?
Find the tension of AB, BC, and BD in pounds.
A gate rotates at point A and releases water when the water's depth, d, exceeds a certain value. The gate's width (perpendicular to the image) is b = 2.95 ft, the water's depth is d = 4.82 ft, and point A is located at h = 2.41 ft. a) What is F, the magnitude of the horizontal force exerted on the gate by the water? The water's specific weight is γw=62.4lb/ft3. b) What are Ax and Bx, the horizontal reaction forces at points A and B that act on the gate from Part A. c) What is dmax, the water's maximum depth before the pressure causes the gate from part A to open?
A semicircular plate of radius 5ft rests vertically on its diameter at the bottom of a pool filled with water to a depth of6ft. Assume that the water’s weight density is62.4lb/ft3.•Find the force exerted by the water against on side of the plate.
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
Question-2: in a container with a depth of 2 m, two separate liquids in two separate compartments are separated from each other through two separate doors A and B. The cap is held in balance with a rope and Mass at the end. find the weight of the mass attached to the rope. (Just find B side)
A magazine rack has a center of gravity 16 cm above the floor, as shown. Through what maximum angle, in degrees, can the rack be tilted without falling over?
1. A vertical semi-circular area of radius r is submerged in a liquid with its diameter in the liquid surface. How far is the center of pressure from the liquid surface? 2. An open vat holding oil (s=0.80) is 8 m long and 4 m deep and has a trapezoidal cross-section 3 m wide at the bottom and 5 m wide at the top. Determine the following: (a) the weight of oil, (b) the force on the bottom of the vat, and (c) the force on the trapezoidal end panel.
a conical tank having a height of 5ft and base of 12 in radius contains 0.7ft^3 of water. How much additional water is needed to fill the tank?
a force is 1.6 kN is applied uniformly on piston of 8 cm diameter. determine the pressure on the piston.