b Chapter 6 File Edit View Help Problem: 20 (of 30) Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your units. The homogeneous rectangular crate weighs 270 lbs and is supported in the horizontal position by the cable at A and the corner hinge at O. If the cable at A is suddenly released, calculate the angular velocity o of the crate just before it strikes the 60° incline. @ = rad/sec 50" A 28" Horiz. 60° Check Answer for this Problem Close

b Chapter 6 File Edit View Help Problem: 20 (of 30) Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your units. The homogeneous rectangular crate weighs 270 lbs and is supported in the horizontal position by the cable at A and the corner hinge at O. If the cable at A is suddenly released, calculate the angular velocity o of the crate just before it strikes the 60° incline. @ = rad/sec 50" A 28" Horiz. 60° Check Answer for this Problem Close

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of rods and disc form a triangle with a spring (a spring connects A to C). The spring has a spring constant of 20 N/m and an unstretched length of 1.5m. each rod has a length of 3m and a mass of 10kg. The disk has a mass of 5kg, a radius of .5 and rolls without slipping. The system starts with an angle between the spring and rods of 60 degrees, determine the angular velocity of the rods after it has dropped to a 30 degree angle.
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
The mass of gear A is 25 kg and its centroidal radius of gyration is 105 mm. The mass of gear B is 13 kg and its centroidal radius of gyration is 85 mm. Calculate the angular acceleration of gear B when a torque of 16 N·m is applied to the shaft of gear A. Neglect friction. The angular acceleration is positive if counterclockwise, negative if clockwise..
Mechanism shown consists of two 8-pound rods AB and CD. each and a 10 lab AD bar. When θ = 0 °, rod AB rotates with an angular velocity of 2 rad / s.If a torque M = 15 lb * ft is applied to rod CD and a force P = 20 lb is applied to bar AD, calculate the angular velocity of bar AB at the instant that θ = 40 °
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
Mechanism shown consists of two 8-pound rods AB and CD. each and a 10 lab AD bar. When θ = 0 °, the rod AB rotates with a velocity angular of 2 rad / s. If a torque M = 15 lb * ft is applied to the rod CD and to the rod AD is applied a force P = 20 lb., calculate the angular velocity of the bar AB at the instant that θ = 40 °
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
1) Three small spheres are rigidly mounted to a horizontal shaft with rotates with angularvelocity omega as shown. Neglect sphere radii, ignore gravity. Spheres have masses m1, m2andm3 as shown.a. What is the angular momentum HO about O the center of the coordinates shown?b. At this instant, what is Ax , the x component of the bearing force at A to offset the dynamicimbalance? Note that you are NOT asked to find any other forces (Ay, Ox, or Oy) in interestof time.
Figure shown represents a schematic diagram of a Porter governor. Each fly ball weighs 16.1 lb and the central weight D is 40 lb. Determine the rotational speed in rpm about the vertical axis AD at which the weight D begins to rise. Answer: n=109 rpm
A rigid body is made of three identical thin rods, each of mass m and length L= 0.6 m,attached together in the form of an H. The body is allowed to fall from the horizontalposition, rotating around one of the legs of the H.a) What is the rotational inertia of the H, in terms of m and L?b) What will be the angular speed of the H when it is oriented vertically?
A uniform rod (mass = 1.8 kg) is 1.5 m long. The rod is pivoted about a horizontal, frictionless pin through one end. The rod is released from rest in a horizontal position. What is the angular speed of the rod (in rad/s) when the rod makes an angle of 23° with the horizontal?. The moment of inertia of the rod about this axis is given by (1/3)ML2.