(b) Determine the following expressions in polar form. (i) v(t) = 40 cos(200t – 60°) V (ii) i(t) = 25 sin(100t + 35°) + 40 cos(100t – 15°) A (iii) Sketch the phasor diagram of Q2(a)(i) and Q2(a)(ii) above.

(b) Determine the following expressions in polar form. (i) v(t) = 40 cos(200t – 60°) V (ii) i(t) = 25 sin(100t + 35°) + 40 cos(100t – 15°) A (iii) Sketch the phasor diagram of Q2(a)(i) and Q2(a)(ii) above.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Related questions

Q: An AC circuits with 50 Hz voltage of 240V effective value is impressed on an inductance of…

Q: 9.48 Given that v,(t) = 20 sin(100t – 40°) in Fig. 9.55, determine i,(t). p's %3D - 10 Ω 30 Ω v, (t)…

A: To find the current in any complex circuit, it is important to convert it into a simple circuit…

Q: Consider the circuit below. The capacitor was initially discharged. at t = 0, the switch is placed…

A: Transient response is the response of a system which is the change in transient(equilibrium) or…

Q: 1A (b) (a) A * N * 220V C 1 kQ 3 uF 50 Hz (c)V R a.) What is the generic name of the circuit given…

Q: Control system stable or not

A: Part (A):- The characteristic equation of the system is, Now, apply the Routh-Hurwitz criterion on…

Q: Assessment Problem 2 The voltage across the terminals of the 5 µF capacitor is 30 cos (4000t + 25°)…

Q: 得分 8. The inductance of an ideal inductor is 0.1 H. The current through the inductor is given by…

Q: QUESTION (b) The maximum values of the alternating voltage and current are 400 V and 20 A…

Q: a. The frequency of the source voltage in the circuit in Fig. 1 is adjusted until vg is in phase…

Q: . Consider a device connected to an ac power supply. The current leads the voltage by 90°, with the…

A: (a) Since the current leads the voltage by 90° the given device is capacitor. (b) The angular…

Q: Consider the circuit diagram where Vs = 2300 20 Vrms V, z, Z, Find: 1. The apparent power delivered…

Q: 6. The characteristic equation of a system is given as s3+25s2+10s+50=0. What is the number of the…

A: The characteristic equation of a system is given as s3+25s2+10s+50=0

Q: 27. A phasor can be represented or expressed in either rectangular form (x +j y) or polar form (z…

A: Choose the correct options Which Statment is right and wrong?

Q: Figure Q2(b) shows the time domain circuit with the voltage source, v,(t) is 25 cos 100t V. The…

A: The solution is given below

Q: Problem: Given a parallel RLC circuit comprised of the following element 00.73-ohm resistor, ideal…

A: True power will be power dissipated in resistor .

Q: 3) A 90 N resistor, a 32 mH inductor, and a 5 µF capacitor are connected in series across the…

Q: TT=3,1416 Find the capacitance of the system (interms of nF) consisting of two air-filled…

Q: In the circuit shown in Figure 1, the source is V1=10 sin ( @t) V where @ = 2n x 200 rad/s. If the…

Q: Figure Q2(b) shows the time domain circuit with the voltage source, v,(t) is 25 cos 100t V. The…

A: The solution is given below

Q: 32. (a) A series connection is formed between a 1 2 resistor, a 1 F capacitor, and a 1 H inductor,…

Q: 1. Using mesh analysis, calculate the current and voltage phasors to describe the voltage across the…

Q: (b) Figure Q2(b) shows the time domain circuit with the voltage source, vs(t) is 25 cos 100t V. The…

A: In an AC circuit all elements work on the same frequency. As the source of the circuit is connected…

Q: The voltage wave propagating on a transmission line is given in real space-time form as v(z, t) =…

Q: i(t) 4 cos (100r – 20°) A( 1 mF 20 mH

Q: DIFFERENTIAL LENGTH, AREA, AND VOLUME Problem solving. Show your solutions and box your final…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: An AC circuits with 50 Hz voltage of 240V effective value is impressed on an inductance of…

A: Given: An AC circuits with Voltage, Vrms=240 V Frequency, f=50 Hz Inductance, L=sin2+2/5 H=0.717 H…

Q: the impedance theoretically of a wire if it carries the frequency 10 kHz have a voltage is 8v, the…

Q: Q1:- A) Find the total capacitance Cr shown in fig.1 if: i. the switch is open ii. the switch is…

A: There are three types of passive elements used in a electric circuit, they are resistance, inductor…

Q: The characteristic equation of a system is given ass3+25s2+10s+50=0. What is the number of the roots…

Q: . Assuming the passive sign convention and an operating frequency of 5 rad/s, calcualte the phasor…

Q: Electrical Engineering A four-element array of isotropic sources is placed along the z-axis. The…

Q: Q1) a). A 1.5 H coil has R of 70 2. The coil is energised by e = 149 sin 314 t. obtain the…

Q: Remaining Time: 59 minutes, 17 seconds. 75% Question Completion Status: A series RLC circuit is…

A: The expression for the given voltage ratio is,…

Q: Electrical Current The current I in a circuit with voltage E, resistance R, capaci- tive reactance…

A: According to the given parameters and instructions in the question, it is required to calculate the…

Q: a) A single-phase AC waveform is represented by the equation; v(t) = 400 sin(3142t + 0.25) V…

Q: 3) For the system shown, in order to plot Root-Locus; a) draw the segment of the Root-Locus on the…

A: We have solved all the subparts.

Q: A sinusoidal voltage v(t) = 150 sin(1000xt + 45°) is depicted in Fig. 1. Evaluate the time ti when…

A: Given, v(t)=150 sin (1000πt+45°) The voltage at time t1 is 0 V as the sinusoid crosses t-axis.…

Q: 2. V2 D-3 Consider the following system -12 D We observe that the response of this system to cos(n)…

Q: Given that the steady-state AC circuit shown operates at a frequency of 400 rad/sec, find the…

Q: A PV system delivers power to a DC motor that in turn feeds a water pump. The DC motor is rated for…

A: The given data is, Power of the DC motor, P = 1 kW Motor efficiency, n = 85 % Number of solar cells…

Q: Figure Q2(b) shows the time domain circuit with the voltage source, vs(t) is 25 cos 100t V. The…

Q: Example 2 Determine r., Z, , Z, (with r,=), A

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: Example 9.7 • The sinusoidal current source in the circuit shown in Fig. 9.18 produces the current…

A: To write the the frequency domain equivalent of the given circuit we must replace capacitor and…

Q: The above figure shows a parallel plate capacitor, where the plate area is A = 34 cm2 and plate…

A: The given capacitor is as shown below, Given, A = 34 cm2 = 3400 mm2 k1 = 4.9, k2 = 2.7 and k3 =…

Q: For the circuit shown below, Given that V 100Z0°Vm and I = 30245°Ams then the values of P, and Q3…

A: Given circuit shown below Vs=100∠0° VrmsIs=30∠45° Arms

Q: 1. A coil of resistance 50 2 and inductance of 100 mH is connected in series with a capacitance of…

Q: The phasor current I, is 5445° A. 1. Find Ia. Ies and Vg. 2. If w = 800 rads/s, write the…

Q: Three currents i,, i, and i, are approaching a node. If i, = 10 sin (400t + 60°) A, and i, = 10 sin…

A: In this question we will find current i 3...

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

POWER SYSTEM

(b) Determine the following expressions in polar form.
(i)
v(t) = 40 cos(200t – 60°) V
(ii) i(t) = 25 sin(100t + 35°) + 40 cos(100t – 15°) A
(iii)
Sketch the phasor diagram of Q2(a)(i) and Q2(a)(ii) above.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

COURSE: Electrical EngineeringSUBJECT: Electrical ApparatusINSTRUCTIONS:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BOX it. PROBLEM:A capacitor in series with a 66 Ω resistor is connected to a 120 V, 60 Hz source. If the impedance of the circuit is 116 Ω, determine the size of the capacitor.
H = 3RM2cos(9ft) where f = frequency, t = time, and the remaining variables are either proportionality constants or material constants. What is the maximum value H could have (algebraic answer)
32. A time domain circuit with v(t) = 100 sin(377t) in 5mS, what is the effective current if the load is 10 ohms? 6.14A 8.67A 7.07A 10A 36. In a series RL circuit, if cos θ = 0.707, the voltage ________ the current by _______. leads, 90 degrees lags, 90 degrees leads, 45 degrees lags, 45 degrees 37. What will happen when an ideal capacitor was installed in parallel with the load? system power factor decreases system power factor increases system will be under voltage system power loss increases 39. Phase angle in a balance circuit has a difference of __________ degrees. 60 90 30 120
A resistor'R' with resistance value of 24 ohm, an inductor 'L' with inductance 20mH, and a capacitor 'C' with capacitance 50 micro Farrad are connected in series with a AC voltage v(t) where v(t) = 50 cos (2 vt + 30 degrees) v. Determine the current i(t) and total impedance if the frequency f is i. 60 Hz ii. 400Hz
Given the following pairs of voltages and currents, indicate whether the element involved is a capacitor, an inductor, or a resistor, and determine the values of C, L or R where ω= 157 rad/s a. v = 2000 sin ωt ; i = 5 cos ωt b. v = 80 sin(157t + 150°); i = 2 sin( 157t + 60°) c. v = 35 sin(ωt − 20°); i = 7 cos( ?? − 110°)
A system has the following characteristic equation: s^4+ s^3+ 3s^2+ 2s + 2 = 0 Using the Routh-Hurwitz method, checka. How many roots are to the right of the imaginary axis?b. Is the system stable?.
The current in the 20 mH inductor is 10 cos(10,000t + 30°)mA.Calculate (a) the inductive reactance; (b) the impedance of the inductor;(c) the phasor voltage V; and (d) the steady-state expression for v(t)
A PV system delivers power to a DC motor that in turn feeds a water pump. The DC motor is rated for 1.0 kW and is 85% efficient. Each PV module has 36 solar cells, arranged in a 9 x 4 matrix. The cell size is 125 mm x 125 mm and cell efficiency is 12%. Calculate the number of modules required in the array. Assume global radiation incidence normal to the panel to be 1.0 kW/m2.
The voltage across the terminals of the 5μF capacitor is 30 cos (4000t + 25°) V. Calculate (a) the capacitive reactance; (b) the impedance of the capacitor; (c) the phasor current I; and (d) the steady-state expression for i (t). 5 μF + v i
An Electric field propagating in free space is given by E(z,t)=40 sin(π108t+βz) ax A/m. The expression of H(z,t) is: Select one: a. H(z,t)=15 sin(π108t+0.33πz) ay KA/m b. H(z,t)=15 sin(π108t+0.66πz) ay KV/m c. H(z,t)=150 sin(π108t+0.33πz) ay A/m d. None of these
A 40 Ω resistor and a 50 μ F capacitor are connected in series and supplied with analternating voltage v = 283 sin 314 t. The supply is switched on at the instant when the voltageis zero. Determine the expression for the instantaneous current at time t.
Using the phase shift of 72º from the Experiment, determine the inductance value, L, of the inductor shown. Vr(t) =3.7272 cos(4000 t - 72°) [V]