Use the exact values you enter in previous answer(s) to make later calculation(s).Consider the following figure. (Assume R, = 32.0 0, R, = 21.0 0, andV = 18.0 V.)R10.0 V5.00 NR2(a) Can the circuit shown above be reduced to a single resistor connected to the baNo. This multi-loop circuit does not contain any resistors in series (i e,connected so all the current in one must pass through the other) nor inparallel (connected so the voltage drop across one is always the same asthat across the other). Thus, this circuit cannot be simplified any further,and Kirchhoff's rules must be used to analyze it.(b) Find the magnitude of the current and its direction in each resistor.R3: 21.0 N =X A5.00 QX AR: 32.0 N =X A

According to Kirchhoff's first law Algebraic sum of current at a junction is always zero

Answered: (b) Find the magnitude of the current…

Science

Physics

(b) Find the magnitude of the current and its direction in each resistor. R3: 21.0 N = X A 5.00 N X A R: 32.0 N = X A

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 64PQ: Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf...

See similar textbooks

Similar questions

Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
A 2.00- and a 7.50F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor.Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
The label on a battery-powered radio recommends the use of a rechargeable nickel-cadmium cell (nicads), although it has a 1.25-V emf, whereas an alkaline cell has a 1.58-V emf. The radio has a 3.20 resistance.(a) Draw a circuit diagram of the radio and its battery. Now, calculate the power delivered to the radio (b) when using a nicad cells, each having an internal resistance of 0.0400 , and (c) when using an alkaline cell, having an internal resistance of 0.200 . (d) Does this differenceseem significant, considering that the radio's effective resistance is lowered when its volume is aimed up?
Consider a series RC circuit as in Figure P18.35 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed. Figure P18.35 Problem 35 and 38.
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
If you were to design an electric heater using Nichrome wire as the heating element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?