(b) shown in Figure 1(b). The tube and the bar are of the same initial length. The combination is compressed between two rigid parallel plates by a force of 500 kN. The diameter of the steel bar is 40 mm, and the inside and outside diameters of the alloy tube are 60 mm and 100 mm respectively. The Young's moduli for steel and aluminium alloy respectively are Est = 200 GNM2, EAI = 70 GNM2. An assembly of a steel bar enclosed within an aluminium alloy tube is Find the stresses generated in the steel bar and the aluminium alloy tube. 500 kN

(b) shown in Figure 1(b). The tube and the bar are of the same initial length. The combination is compressed between two rigid parallel plates by a force of 500 kN. The diameter of the steel bar is 40 mm, and the inside and outside diameters of the alloy tube are 60 mm and 100 mm respectively. The Young's moduli for steel and aluminium alloy respectively are Est = 200 GNM2, EAI = 70 GNM2. An assembly of a steel bar enclosed within an aluminium alloy tube is Find the stresses generated in the steel bar and the aluminium alloy tube. 500 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.13P: Rectangular bars of copper and aluminum are held by pins at their ends, as shown in the figure. Thin...

See similar textbooks

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
Rectangular bars of copper and aluminum are held by pins at their ends, as shown in the figure. Thin spacers provide a separation between the bars. The copper bars have cross-sectional dimensions 0.5 in. × 2.0 in., and the aluminum bar has dimensions 1.0 in. × 2.0 in. Determine the shear stress in the 7/16-in. diameter pins if the temperature is raised by 100°F. (For copper, Et= 18,000 ksi and ac = 9.5 × 10-6/?; for aluminum, Ea= 10,000 ksi and aa= 13 × 10-6/?.) Suggestion: Use the results of Example 2-10
An elastomeric bearing pad consisting of two steel plates bonded to a chloroprene elastomer (an artificial rubber) is subjected to a shear force V during a static loading test (see figure). The pad has dimensions a = 125 mm and b = 240 mm, and the elastomer has a thickness t = 50 mm. When the Force V equals 12 kN, the top plate is found to have displaced laterally S.O mm with respect to the bottom plate. What is the shear modulus of elasticity G of the chloroprene?
A disk of SBR elastomer 3.0 cm in diameter 0.5 cmthick is used as a cushioning surface between two steel rods ofthe same diameter, as shown below (not to scale). a. If the rods are brought together with an axial force of 100 N such that the SBR is compressed elastically between them, what is the thickness of the SBR under load? b. Under the same conditions as part (a), what is the greatest possible diameter of the SBR under load? c. If the SBR is bonded to the rods, how far can one rod be rotated with respect to the other before the SBR/rod interface fractures? Assume that the rods are essentially rigid and the distance between them remains constant. Please answer in degrees of rotation.
A 200 kg load is hung on a wire of length 4 m, cross sectional area of 0.2 x 10 -4 m2 and Young’s modulus of 8 x 1010 Pa. What is its increase in length?
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
A cylindrical component 0.3 m long is solid for 1/3 of its length and hollow with inner diameter ½ the outer diameter for the rest of the length. At 300C a gap of 0.1 mm exists between the component and the rigid supports. The outer diameter is 60 mm and the stress is not to exceed 150 MN/m2. Determine the maximum temperature that will not cause failure of the component. Take α as 1.3x10-5/0c and E as 200 GN/m2
Kindly show a step-by-step solution. Thank you A 6m rod with a 4mm gap between one of its ends and the surface of the wall next to it is secured solidly between two walls at 25°C. Calculate the highest temperature that the rod can withstand in degrees celsius while taking into account the maximum limiting stress of 67 MPa, where a = 19.5 m/mC°, and E = 130 GPa.
THIN-WALLED VESSELa. What is a thin-walled vesselb. Derivation of stress formula for thin-walled vessel (cylindrical and spherical)c. Step by step solution of 2 sample problems each for cylindrical and spherical vessel
A steel bolt 8mm diameter fits loosely inside aluminum tube 8mm diameter and 16mm outside diameter.A knot is fitted onto the bolt and tighten against the tube until the stress in the bolt is 40N/m^2.Calculatebthe stress in the bolt.If the temperature of the assembly is now increased by 100°C,what will be the new value of stress in each components. E=200kN/mm^2 for the steel E=70kN/mm^2 for aluminium And coefficient of linear expansion per degree celcius of both steel and aluminum is 10×10^-6/°C and 20×10^-6/°C
A steel rod, 12 mm in diameter, passes centrally through a copper tube 2.5 m long and having 36 mm and 48 mm as internal and external diameters respectively. The tube is closed at each end by 24 mm thick steel plates which are secured by nuts. The nuts are tightened until the copper tube is reduced in length by 0.50. The whole assembly is then raised in temperature by 60 degrees Celsius. Steel: Coefficient of expansion = 1.2x10^-5/degrees Celsius, Es = 200 GPa Copper: Coefficient of expansion = 1.75x10^-5/degrees Celsius, Ec = 100 GPa Calculate the stress in copper and stress in steel after the rise of temperature if the thickness of the plates remains unchanged. Indicate if the answer is tensile, tension, compression.
A steel rod, 12 mm in diameter, passes centrally through a copper tube 2.5 m long and having 36 mm and 48 mm as internal and external diameters respectively. The tube is closed at each end by 24 mm thick steel plates which are secured by nuts. The nuts are tightened until the copper tube is reduced in length by 0.50. The whole assembly is then raised in temperature by 60 degrees Celsius. Steel: Coefficient of expansion = 1.2x10^-5/degrees Celsius, Es = 200 GPa Copper: Coefficient of expansion = 1.75x10^-5/degrees Celsius, Ec = 100 GPa Calculate the stress in copper before the rise of temperature if the thickness of the plates remains unchanged. Indicate if the answer is tensile, tension or compression