Kindly show a step-by-step solution. Thank you A 6m rod with a 4mm gap between one of its ends and the surface of the wall next to it is secured solidly between two walls at 25°C. Calculate the highest temperature that the rod can withstand in degrees celsius while taking into account the maximum limiting stress of 67 MPa, where a = 19.5 m/mC°, and E = 130 GPa.

Kindly show a step-by-step solution. Thank you A 6m rod with a 4mm gap between one of its ends and the surface of the wall next to it is secured solidly between two walls at 25°C. Calculate the highest temperature that the rod can withstand in degrees celsius while taking into account the maximum limiting stress of 67 MPa, where a = 19.5 m/mC°, and E = 130 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.7P: A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of...

See similar textbooks

Similar questions

Rectangular bars of copper and aluminum are held by pins at their ends, as shown in the figure. Thin spacers provide a separation between the bars. The copper bars have cross-sectional dimensions 0.5 in. × 2.0 in., and the aluminum bar has dimensions 1.0 in. × 2.0 in. Determine the shear stress in the 7/16-in. diameter pins if the temperature is raised by 100°F. (For copper, Et= 18,000 ksi and ac = 9.5 × 10-6/?; for aluminum, Ea= 10,000 ksi and aa= 13 × 10-6/?.) Suggestion: Use the results of Example 2-10
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of elasticity E = 29,000 ksi and coefficient of thermal expansion a = 6.5 ×10-6 /?. If the temperature of the beam is raised uniformly by an amount AT = 20°F, calculate the thermal stress aTin the beam.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal diameter, of exactly the same length. The two pieces are rigidly fixed together by two transverse pins 20mm in diameter,one at each end passing through both rod and the tube. Calculate the stresses induced in the copper rod, steel tube and the pins if the temperature of the combination is raised by 50°C, take: E,= 210 GPa and a,= 0.0000115 per deg C. E= 105 GPa and a,= 0.000017 per deg C. Calculate the stresses induced in the copper rod. steel tube. Calculate the stresses induced in the pins if the temperature of the combination is raised by 50°C,
a 20mm diameter bronze bar 3.4m long is place between two rigid walls. at a temperature of -31°C, the gap ∆= 4.7mm. Find the temperature (at degree Celsius) at which the compressive stress in the bar will be 39MPa . Use alpha = 19.59x10^-6 m/(m.°C) and E= 87GPa.
Steel crane rails of the MRT are laid with their adjacent ends 3.2 m apart when the temperature is 15 °C. The length of each rail is 18 m. The coefficient of thermal expansion is 11.7 x 10-6 m/m.ºC. Use E= 200 GPa. a) Determine the temperature at which the rails will touch end to end. b) Determine the gap between adjacent ends when the temperature drops to -10°C. c) Determine the compressive stress in the rails when the temperature reaches 45 °C.
A steel railroad rails 10m long are laid with end-to-end clearance of 3mm at a temperature of 15C. (a) At what temperature will the rails just come in contact? (b) What stress would be induced in the rails at that temperature if there were no initial clearance? Use a=11.7x10^-6C and E=200GPa -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong. -Show complete solution and explanation for the answers
1) Thehorizontal steel rod, 2.5 m long and 1200 mm 2 in cross sectional area, is secured betweentwo walls as. If the rod is stress free at 20 C, compute the stress when the temperature hasdropped to -20 C. Assume that the walls do not move. Use α = 11.7 x 10 6/ C and E = 200 GPa