Question is in image a) The principal stresses. Sketch the results on a properly oriented element and specify the orientation.b) The maximum in-plane shear stress and average normal stress. Sketch the results on a properly orientedelement and specify the orientation.c) The absolute maximum shear stress.Clearly show all Mohr's circle work and annotate all stresses and their values.Problem 5:200 MPa500 MPa++Y350 MPa

b) The maximum in-plane shear stress and average normal stress. Sketch the results on a properly ori element and specify the orientation. c) The absolute maximum shear stress. Clearly show all Mohr's circle work and annotate all stresses and their values. oblem 5: 200 MPa 500 MPa ++Y 350 MPa

b) The maximum in-plane shear stress and average normal stress. Sketch the results on a properly ori element and specify the orientation. c) The absolute maximum shear stress. Clearly show all Mohr's circle work and annotate all stresses and their values. oblem 5: 200 MPa 500 MPa ++Y 350 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.18P: -18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a)...

See similar textbooks

Related questions

Q: A) Find the principal Stresses B) Find the Maximum Shear Stress 30 MAa $45 MPa 60 MPa

Q: At a point in a stressed body, the cartesian components of stress are Oxx = 60 MPa, Guy = -40 MPa,…

A: Given Data σxx=60 Mpa σyy=-40 Mpa σzz=20 Mpa τxy=-40 MPa τyz=20 MPa τxz=30 MPa Stress tensor,…

Q: For the state of stress given below, a) Determine principal stresses and principal planes b)…

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A: A perpendicular force applied on a body per unit area is referred to as a stress. There are three…

Q: 6. In a plane stress condition, the components of stress at a point are o, =20 MPa, oy =80 MPa and…

Q: 4. Mohrs Circle construction for generalized plane stress

A: Mohr's Circle of Generalized plane Stress.

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: 2 -1 o =|-1 2 1 -1 2 -1 Find (a) Principal stress (b) Principal directions (c) Invariant

A: TO FIND: (a) Principal stress (b)principal direction (c) Invariants GIVEN: stress tensor:…

Q: The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If…

Q: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind…

A: Given Data σx=20 kpsiσy=-10 kpsiτxy=-8 kpsi Draw the diagram

Q: Principal stresses:σ1=31.69 MPa σ2=−30.56 MPa Maximum in−plane stress: σmax=31.69 MPa

Q: Stress Transformation & Mohrs Circle Consider a stress point in a structural member that is…

A: Given data: σx=60 MPaσy=90 MPaτxy=30 MPa Need to determine the principal stresses and maximum shear…

Q: Determine the minor principal stress and position of the principal plane when a block is subjected…

Q: Find the normal, tangential and the resultant stress & its inclination on a plane making an angle of…

Q: The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the…

A: The data given in this question, Force, P=1800 N, and F=2500N The inner radius of the pipe, ri=24…

Q: Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension),…

Q: Figure 1 shows an element ith stresses. Angle 1 Tyx Tyx Figure 1 Point C)- x-direction stress…

A: The three basic equations to determine the stress at various cross-sections are:…

Q: Problem 1-5 The Cartesian components of stress at a point are given below : Oy = 5, Tyz = - 4,…

Q: Find the maximum shear stress if maximum principal stress is 30 MPa Minimum principal stress 20 Mpa

Q: 1- The principal stresses or a point in the section of a member are 50 MPa or 20 MPa both tensile.…

A: To find : The normal and shear stress. Given : The principal stresses are σ1=50 MPa. σ2=20 MPa.…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: 2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m?…

Q: Q3/ Using Mohr's circle find out the principle stresses and the maximum shear stress and the stress…

Q: - The state of plane stress is represented by the stress element below. Draw the Mohr's circle,…

Q: Angle 1 Oy Tyx Figure 1 Point A(-x-direction stress 60MPA(compression), y-direction stress…

A: The given values are - σx = -60MPa , σy = 40MPa, τxy = -30MPaθ = 30° The stresses on inclined plane…

Q: 60 MPa 30 MPa 45 MPa

A: On the given element, Stress in x direction = σx = 45 MPa Stress in y direction = σy = -60 MPa…

Q: Quiz// For the state of stress shown in Figure below. Draw the Mohr's circle and find the principal…

Q: (tensile), minor stress of 40 MPa (tensile) along with a counter clockwise shear stress of 30 MPa.…

Q: The state of an element is shown in figure Fig. - 1. Use to find the stresses and planes of stress…

A: The Mohr's circle is nothing but the representation of the stresses in the material on a circle. The…

Q: At a point on the surface of a pressurized cylinder, the material element is subjected to stresses;…

A: (1)

Q: 2- The state of plane stress at a point with respect to the xy-axes is shown in Fig, find the normal…

A: To find : The normal and shear stress on section inclined at an angle of 30° Given : The stress in…

Q: 2- The normal stress in an inclined plane is 21.782 Mpa, the stress in the x-axis is 35 Mpa, in the…

Q: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and their…

Q: Consider the following plane stress state: Oх- 40 MPа, дy- 30 МРа, Тҳу— 20 MРа ссw Calculate the…

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

Q: na stressed element, the value of normal stress along 'X' and 'Y' directions are 200 MPa (tensile)…

Q: 2. For the state of plane stress given, determine the principal planes, the principal stresses and…

A: givenstress in x direction σx=100MPa tensile stress in y direction σy=-60MPa compressive shear…

Q: 8. Principal planes are those planes on which a. Normal stress is maximum b. Normal stress is…

A: Principal planes are the planes inside the material at which the shear stress is zero.

Q: The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane…

A: (a) To find: The principle stress. Given: The stress in x-direction is σx=-85 MPa. The stress in…

Q: 3. At the point labeled A in the bracket below, the stresses are og = 4.8 ksi, o, = -1.2 ksi and Ty…

Q: Calculate the normal stress and shear stress acting on the plane 2x+y+2z=1 passing thorough a point…

A: given; plane ;2x+y+2z=1stress at point (σ)=162022000023

Q: 10 MPa 9. Using Mohr's circle, for the figure at the right, determine: a) The angle to the principal…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Q#2: Explain the absolute maximum shear stress. Construct Tresca's hexagon by explaining all the…

A: Given data To explain the absolute maximum shear stress and construct by Tresca’s hexagon by…

Q: Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: The stress stress after rotation is given by - τnt=-σx-σy2sin2α + τxycos2α In first case-…

Q: The state of stress at a point 0 in a loaded member relative to the X, Y and Z axes is as below.…

Q: (a) The plane stress at a point with respect to x-y-axes is shown in Fig. Q1(a). By using…

A: according to the given details:

Q: hear stress element. Any stress components not shown are assumed to be zero. Work problem #4

A: Part A) First, draw the coordinate system and depict the given point in the below expression.

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

Question is in image

a) The principal stresses. Sketch the results on a properly oriented element and specify the orientation.
b) The maximum in-plane shear stress and average normal stress. Sketch the results on a properly oriented
element and specify the orientation.
c) The absolute maximum shear stress.
Clearly show all Mohr's circle work and annotate all stresses and their values.
Problem 5:
200 MPa
500 MPa
++Y
350 MPa

Expert Solution

Step 1

A: Formula:

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 6.5 MPa in the vertical direct ion. Also, shear stresses of magnitude 12.5 MPa act in the directions shown (see the figure for Problem 7.2-8). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?