The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number

The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: 1) Determine the average braking torque to be applied to stop the vehicle of mass 1.5 ton is moving ...

Q: All physical quantities involve a direction

A: Given Physical quantity To find Direction based physical quantity

Q: The figure below shows the stress-strain diagrams of four different materials A, B, C, and D. Which ...

A: The stress-strain diagrams of four different materials are given.

Q: What unit operations are applied in manufacturing a car? Give at least 4 unit operations and explain...

A: There are many operations involved in the manufacturing of the car, But there are main operations ar...

Q: nd its distance from outer cylinder to the inner cylinder is 0.0364". The said outer cylinder of the...

Q: A circular bar of "500" mm length is supported freely at its two ends. It is acted upon by a central...

Q: The initially closed valve in Figure III..6.1(b) suddenly opens. Find the flow velocity 5 seconds af...

Q: 1. A simply supported beam AB of span 4 m is carrying a point loads of 5, 2 and 3 kN at 1, 2 and 3 m...

A: We will answer the first question since the exact one was not specified. Please resubmit the questio...

Q: 4 inches diameter steel shaft rotates at 245 rpm. if the shearing stress is limited to 11 ksi, deter...

A: Given:d=4 inN=245 rpmζ=11 ksi =11*103 psi

Q: A cylindrical bar shown in the figure below has axial loads applied as illustrated. Calculate the no...

A: As per given We have to find stress in bar of section AB, BC and CA

Q: Pieces of sheet metal are to be U-formed using a single-acting cylinder. The start signal is to be g...

A: Solution: The Pneumatic circuit diagram using the ISO symbols is shown below:

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

Q: The force F, acting in a constant direction on the 22-kg block, has a magnitude that varies with the...

A: Answer: The block must slide a distance of 22.4 m.

Q: A steel marine propeller shaft 13 inches in diameter and 15 ft long is used to transmit 9,426 hp at ...

A: GIVEN DATA- D=13in L=15ft P=9426hp N=189rpm G=12*10^6 psi WE HAVE TO FIND SHEAR STRESS

Q: The clamping of a work piece is to be controlled by either of two Push buttons. A further push butto...

Q: The tailgate OBČ is attached to the rear of a trailer via hinges at O and two restraining cables AB....

Q: ows that the shear modulus of an aluminum specimen is 4.6 x 106psi. When the same specimen is used i...

Q: A sub-marine with its axis 15 m below water surface fitted with pitot tube moves horizontally in sea...

Q: The rectangular plate is deformed into the shape shown by the dashed lines. If ?? has a normal strai...

Q: 1. Determine the other properties of the steam for the following conditions

A: Dear Student As per guidelines i am allowed to solve first question only ( incase of multiple questi...

Q: For Hibiscus and Rose Groups A steel helical spring is wound from No. 14 music wire with a mean heli...

Q: 1. At the beginning of the compression process in a hot-air-standard Otto cycle, the air is at 100 k...

Q: 2/ Steam is contained in a closed rigid container. steam are 1.5 MPa and 240°C, respectively. The te...

A: Volume of rigid container = 0.5 m2 Initial pressure(P1 )= 1.5 MPa initial temperature(T1 )= 240 C ...

Q: A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed = ...

Q: A simply supported beam of length L=12 m, carrying UDL 10 KN/m in its entire length of thebeam. Draw...

Q: The airfoil section below is extracted from Meirovitch book Figure 5.24 (associated with problem 5.5...

A: given; number of link(l)=4number of joint(j)=4number of higher pair (h)=0

Q: Fluid: Consider the following two tank system, where an input flow enters the first tank with flowra...

Q: 1. The heat supplied to the system equals increase in the internal energy. Select one: True False ...

Q: Determine the composition of the phases;

A: Phase Equilibrium: Equilibrium is the lowest energy state for a given T, P, and composition (i.e., w...

Q: In a rack and pinion steering system, what protects the rack from contamination? a. The inner tie-ro...

A: A gear set converts the circular motion of the steering wheel into the linear motion necessary to...

Q: A 50-mm-diameter aluminum compound shaft is loaded by torques at the gears as shown in the figure. D...

Q: Define a pure compound refrigerant, and give two examples.

A: A refrigerant is a working fluid used in the refrigeration cycle of air conditioners and heat pum...

Q: For a profit-maximizing monopoly that charges the same price to all consumers, what is the relations...

A: A profit maximizer is a vital feature of a monopolist. There is no competition in a monopolistic ...

Q: A gas flows through a square conduit, at the entrance the conduit sides are 10 cm, the velocity is 7...

Q: A wheel tractor has a 200HP engine.if it is operating at an altitute of 1000m above sea level, at an...

Q: A piece of metal weighs 350 N in air and when it is submerged completely in water it weighs 240 N a...

Q: A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on ...

Q: the value of Joule-Thomson

A: Given; For an ideal gas, the value of Joule- Thomson co-efficient is: So, For ideal gas, PV=RT T=∂V∂...

Q: 1 N 3 N 0.25 m 5 N For this example you will be 0.45 m calculating it around the COG (g on the diagr...

Q: simple band brake

A: The simple band brake is consists of one or more ropes or belt or steel band having friction lining ...

Q: 1. Loads are applied on a pipe made up of steel, bronze and aluminum. The forces and areas are shown...

A: Given:P=3000 lbA=0.5 in2

Q: What is the polar moment of inertia of a solid steel shaft in mm^4 that will not twist through more ...

Q: A prismatic vessel has two sections A and B connected by an orifice 0.3m square with C = 0.60. The h...

A: given; →area at A (A1)=10m2→area at B (A2)=40m2→lets take velocity at A=V1→lets take velocity at A=V...

Q: The position of a particle along a straight line is given by s = (1.5t3 – 13.5t2 + 22.5t), where t i...

Q: Find the velocity, acceleration, and speed of a particle with the given position function. r(t) = ti...

A: Given, Position function = r(t) = t2 i + 8t j + 3 ln(t) k From position function, velocity functio...

Q: The force F, acting in a constant direction on the 22-kg block, has a magnitude that varies with the...

Q: Calculate the specific weight, density, specific volume and relative density of oil which has weight...

A: GIVEN DATA- A OIL HAS WEIGHT 7N/litre WE HAVE TO FIND WEIGHT DENSITY , DENSITY , SPECIFIC VOLUME AND...

Q: 11 MPa 14.04 MPa ne diagram given above, we have E = 90 MPa, v = 0.35 O Determine the stress state m...

Q: centroidal moment of Inertia

Q: Imagine that a fluid velocity field can be found with the same motion rotation of a CD inside a CD ...

A: Voticity is described as local spinning motion of a fluid as seen by an observer located at a point ...

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
A hollow steel shaft, 6 ft long, has an outer diameter of 3.07 in. and an inner diameter of 1.5 in. The shaft is transmitting 168 hp at 102 rev/min. Determine the maximum shear stress (in psi) in the shaft. Round off the final answer to two decimal places.