b. A system is characterised by a signal flow graph shown in figure 1.UseMason's gain formula to prove that the transfer function of the systemcan be determined.Gz 6/ G3-H1-H2Fig 1c. In a simulation to determine the stability of a system, the transferfunction below was obtained; use Routh Array Criterion to prove thatthis system is unstable.2s+5H(s)(s+3)(s+2)(s+5)+s++1

In this question we will find transfer function of given system using Masons gain formula.... Note:-…

b. A system is characterised by a signal flow graph shown in figure 1.Use Mason's gain formula to prove that the transfer function of the system can be determined. G2 6/ G3 -H1 -H2 Fig 1 c. In a simulation to determine the stability of a system, the transfer function below was obtained; use Routh Array Criterion to prove that this system is unstable. 2s+5 H(s) (s+3)(s+2)(s+5)+s++1

b. A system is characterised by a signal flow graph shown in figure 1.Use Mason's gain formula to prove that the transfer function of the system can be determined. G2 6/ G3 -H1 -H2 Fig 1 c. In a simulation to determine the stability of a system, the transfer function below was obtained; use Routh Array Criterion to prove that this system is unstable. 2s+5 H(s) (s+3)(s+2)(s+5)+s++1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
A controller is designed so that the nominal closed-loop transfer function has bandwidth 1.9 rad/s and rolls off with -40dB/dec at high frequencies. If the model has multiplicative uncertainty above 10.7 rad/s, what is the maximum uncertainty gain in dB that can be tolerated according to the Small Gain Theorem?
A filter is provided with a cascaded differential amplifier. The midband gain and noise coefficient of the filter are given as −3 dB and 3 dB, respectively. According to this, b) Find the noise coefficient of the cascaded system
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 42.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit.NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
Design a single-sideband AM modulator and demodulator units based on following rules. Design Principles: bandwidth of filter you will design will be 6kHz in case of double sideband solutions. the carrier frequency is 4MHz. a) Determine the values of elements (if any; R, C, and L) used in the circuits. b) In case of noise (added to the modulated signal, What can be the SNR at i/p stage of demodulator? What can be the SNR at o/p stage of demodulator?
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 7.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit. NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
Obtain the overall transfer functions for the following signal flow graphs using mason’s gain formula..
A filter is provided with a cascaded differential amplifier. The midband gain and noise coefficient of the filter are given as −3 dB and 3 dB, respectively.According to this,a) If it is known that the amplifier gain is ?1= 20 dB and the noise coefficient is ?1= 2 dB, calculate the midband gain for the entire cascaded system. Give your answers in dB
(a) Design a low-pass amplifier (i.e., choose R1,R2, and C) to have a low-frequency input resistanceof 10 k ohm, a midband gain of 20 dB, and abandwidth of 20 kHz. (b) Choose element valuesfrom the table.
Apply Mason’s Rule to calculate the transfer function of the system represented by following Signal Flow Graph
Derive the transfer function of the process from the block diagram shown in the figure.
An analog signal, with an absolute bandwidth of 10 KHz, is to be converted to a digital signal usingan A/D converter and stored in a PC. If the quantization error must be within ±0.05% of the peak-to-peakvalue of the analog signal, determine the storage requirement. Please assume that we are going to record 8seconds of data, sampled at 1.5 times the Nyquist rate.