Beal eyeks A 0.8-m insulated rigid tank contains 2 kg of carbon dioxide at 90 kPa. Now paddle- wheel work is done on the system until the pressure in the tank rises to 150 kPa. Determine the minimum paddle-wheel work of this process. Take To =300 K (R = %3D 0.189kJ 0.68kJ

Beal eyeks A 0.8-m insulated rigid tank contains 2 kg of carbon dioxide at 90 kPa. Now paddle- wheel work is done on the system until the pressure in the tank rises to 150 kPa. Determine the minimum paddle-wheel work of this process. Take To =300 K (R = %3D 0.189kJ 0.68kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q 3) Steam enters an adiabatic turbine at 6 MPa and 500°C at a rate of 3 kg/s and leaves at 25 kPa.…

Q: An insulated rigid tank contains 2 lbm of air at 20 psia and 70°F. A paddle wheel inside the tank is…

A: Write the equation for entropy change in the system. Here is the entropy change of the system, cv…

Q: A 3-m3 rigid tank contains nitrogen gas at 500 kPa and 300 K. Now heat is transferred to the…

A: Given data: The initial pressure of the nitrogen gas in a rigid tank is P1=500 kPa. The initial…

Q: A 0.5-m3 rigid tank contains nitrogen gas at 600 kPa and 300 K. Now the gas is compressed…

Q: A 0.6-m rigid tank contains refrigerant-134a initially at 200 kPa and 40 percent quality. Heat is…

A: The volume of the rigid tank = 0.6 m3The initial pressure of the refrigerant P1 = 200kPaThe quality…

Q: A piston-cylinder device contains 0.35 kg of air initially at 2423 kPa and 321 oC. The air is first…

Q: Steam at 1000 kPa, a temperature of 300°C, and a velocity of 50 m/s. The steam leaves the turbine at…

Q: Nitrogen gas is compressed from 80 kPa and 27°C to 480 kPa by a 10-kW compressor. Determine the mass…

A: Given: The initial pressure of the nitrogen gas in the compressor is P1=80 kPa The final pressure of…

Q: eters the compressor as a saturated vapor at 10°C and leaves the compressor at 1400 kPa with an…

Q: Refrigerant-134a enters an adiabatic compressor as saturated vapor at 30 psia at a rate of 20 ft3…

A: The initial enthalpy and entropy of the refrigerant is The process of compression is isentropic;…

Q: A 1200-W electric resistance heating element whose diameter is 0.5 cm is immersed in 40 kg of water…

A: The data given is, Total power of the electric heater, P = 1200 W The diameter of element, d = 0.5…

Q: 3. Steam enters an adiabatic turbine steadily at 8Mpa and 500C at a rate of Skg/s and leaves at…

Q: A piston–cylinder device initially contains 15 ft3 of helium gas at 25 psia and 70°F. Helium is now…

A: Given data: Initial volume, V1 = 15 ft3 Initial pressure, P1 = 25 psia Initial temperature, T1 =…

Q: An insulated piston–cylinder device contains 5 L of saturated liquid water at a constant pressure of…

A: Given: The volume of water, V = 5 L The pressure of water, P = 150 kPa The energy required to…

Q: Air at 27°C and 100 kPa is contained in a piston– cylinder device. When the air is compressed…

A: Given, T1 = 27°C = 27+273 = 300 K P1 = 100 kPa T1 = 27°C = 27+273=300°K W = 1000 kJ P2 = 600 kPa m=?…

Q: Steam enters an adiabatic turbine at 2Mpa and 250C and expands to 25kPa with an isentropic…

A: To find: The power output of this turbine. Given: The inlet pressure to adiabatic turbine is P1=2…

Q: Refrigerant-134a at 100 kPa and –10°C is compressed by an adiabatic compressor to 600 kPa and 50°C.…

Q: Nitrogen at 120 kPa and 30°C is compressed to 600 kPa in an adiabatic compressor. Calculate the…

A: The initial temperature of the nitrogen is T1=30 °C. The initial pressure of the nitrogen is P1=120…

Q: Steam enters an adiabatic turbine at 8 MPa and 500°C at a rate of 3 kg/s and leaves at 20 kPa. If…

A: Given, P1 = 8 MPa T1 = 500°C P2 = 20 kPa = 0.02 MPa m = 3 kg/s W = 2.5 MW = 2.5 x 103 kW T2 =?

Q: 1) Helium is to be compressed from 150 kPa and 300 K to 800 kPa and 500 K. A heat loss of 20 kJ/kg…

Q: Helium gas is compressed from 16 psia and 85°F to 120 psia at a rate of 10 ft3 /s. Determine the…

A: Given: The initial pressure of the Helium gas is P1=16 psia. The final pressure of the pressure is…

Q: Air is compressed by an adiabatic compressor from 100 kPa and 12°C to a pressure of 800 kPa at a…

A: Given Data: The inlet pressure is P1 = 100 kPa. The inlet temperature is T1 = 12°C. The exit…

Q: A 200-m3 rigid tank initially contains atmospheric air at 100 kPa and 300 K and is to be used as a…

A: Given: The volume of tank V= 200 m3. The atmospheric pressure and temperature are P0=100 kPa and…

Q: An insulated piston–cylinder device contains 0.05 m3 of saturated refrigerant- 134a vapor at 0.8-MPa…

A: Givan data, P1 = 0.8 MPa P2 = 0.4 MPa V1 = 0.05 m3 It is given in question that the expansion…

Q: A hair dryer is basically a duct in which a few layers of electric resistors are placed. A small fan…

A: P1 = 100 kPa T1 = 295 K Q ˙= 1200 J/s T2 = 320 K A2 = 60 cm2 Control volume of a given problem is…

Q: A hair dryer is basically a duct in which a few layers of electric resistors are placed. A small fan…

A: Given Data:- P =1200w P1=100kPa T1 =22°C…

Q: Helium gas is compressed from 16 psia and 85°F to 120 psia at a rate of 10 ft3 /s. Determine the…

A: Solution: Step-1 Given: The initial pressure of the Helium gas is P1=16 psia. The final pressure of…

Q: Explain the Reversible work relations for steady-flow and closed systems.

Q: A piston–cylinder device initially contains 3 lbm of liquid water at 20 psia and 708F. The water is…

A: For state 1 we have, From the steam table, it is clear that this is a compressed liquid.

Q: A piston-cylinder device initially contains 1.4 kg of refrigerant-134a at 100 kPa and 20oC. Heat is…

Q: Steam expands in a turbine steadily at a rate of 18,000 kg/h, entering at 7 MPa and 600°C and…

A: Given: mass flow rate(m) =18000 kg/h = 5kg/sP1=7MPa =7×106 PaT1=600°C=873 KP2=50 kPaSurrounding…

Q: What is the minimum internal energy that steam can achieve as it is expanded adiabatically in a…

A: Given: The initial pressure of the steam, P1 = 1500 kPa The final pressure of the steam, P2 = 100…

Q: A 0.8-m3 rigid tank contains carbon dioxide (CO2) gas at 250 K and 100 kPa. A 500-W electric…

A: Given, Before Heater is on, P1 = 100 kPa T1 = 250 K V1 = 0.8 m3 After Heater is on, P2 = 175 kPa…

Q: One lbm of R-134a is expanded isentropically in a closed system from 100 psia and 100°F to 10 psia.…

A: Given R-134a Internal pressure = 100 psia Temperature = 100o F Minimum pressure = 10 psia Mass = 1…

Q: A piston–cylinder device initially contains 1.4 kg of refrigerant-134a at 100 kPa and 20°C. Heat is…

A: The value of specific volume at an initial point having P1=100 kPa, T1=20°C and at the final point…

Q: Saturated refrigerant-134a vapor at 15 psia is compressed reversibly in an adiabatic compressor to…

A: Given data P1=15 psiaP2=80 psia

Q: A piston cylinder arrangement contains 0.02 m³ of air at 50°C and 400 kPa. Heat is added in the…

A: Given Data V1=0.02 m3 T1=50°C T2=700°C P=400 kPa=constant Q=-50 kJ

Q: Steam enters a turbine steadily at 7 MPa and 600°C with a velocity of 60 m/s and leaves at 25 kPa…

A: At 7Mpa, 600°C (From steam table) C1=60 m/s A1=150 cm2 v1=0.05566 m3/Kg At 25KPa A2= 1400Cm2…

Q: A 0.05-m3 rigid tank initially contains refrigerant134a at 0.8 MPa and 100 percent quality. The tank…

A: Given Volume of tank = 0.05 m3 Pressure in tank = 0.8 MPa Quality = 100% Valve pressure = 1.2 MPa…

Q: An air compressor takes in air at 30 °C and 100 kPa and then compressed adiabatically until its…

A: Step 1: Given data: The temperature of air at the inlet of compressor T=30°C=30°C+273 K=303 K.…

Q: Determine the work required (in kJ/kg) for a pump that is used to increase the pressure of a liquid…

A: Given: P1 = 100 kPa P2 = 1500 kPa , v = 0.001031 m3/kg Work required for pump to increase the…

Q: A piston–cylinder device initially contains 3 lbm of liquid water at 20 psia and 70°F. The water is…

A: Assumptions - Tank is stationary → ΔKE =ΔPE = 0 - Process is quasi-equilibrium…

Q: Refrigerant-134a enters an adiabatic compressor as saturated vapor at 100 kPa at a rate of 0.7 m3…

A: Given, Compressor inlet (saturated vapor), P1=100 kPa Q1˙=0.7 m3/min=0.760 m3/sec=0.0116 m3/sec…

Q: A 0.8-m3 insulated rigid tank contains 1.54 kg of carbon dioxide at 100 kPa. Now paddle-wheel work…

Q: Refrigerant-134a enters an adiabatic compressor as saturated vapor at 30 psia at a rate of 20 ft3…

Q: Refrigerant-134a is compressed steadily from the saturated vapor state at 140 kPa to 1.2 MPa and 60…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

Baal eyels
A 0.8-m insulated rigid tank contains 2 kg of carbon dioxide at 90 kPa. Now paddle-
wheel work is done on the system until the pressure in the tank rises to 150 kPa.
Determine the minimum paddle-wheel work of this process. Take To =300 K (R =
0.189RJ
%3D
0.68 J
kgK
kgK
FO Uring constant specific heats at room

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refrigerant-134a is expanded adiabatically from 100 psia and 100°F to a pressure of 10 psia. Determine the entropy generation for this process, in Btu/lbm·R.
Helium gas is compressed from 16 psia and 85°F to 120 psia at a rate of 10 ft3 /s. Determine the power input to the compressor, assuming the compression process to be isentropic.
Helium gas is compressed from 16 psia and 85°F to 120 psia at a rate of 10 ft3 /s. Determine the power input to the compressor, assuming the compression process to be ideal two-stage polytropic with n = 1.2.
Refrigerant-134a at 140 kPa and –10°C is compressed by an adiabatic 1.3-kW compressor to an exit state of 700 kPa and 60°C. Neglecting the changes in kinetic and potential energies, determine the volume flow rate of the refrigerant at the compressor inlet in L/min.
A 5-ft3 rigid tank initially contains refrigerant-134a at 60 psia and 100 percent quality. The tank is connected by a valve to a supply line that carries refrigerant-134a at 140 psia and 80F. The valve is now opened, allowing the refrigerant to enter the tank, and is closed when it is observed that the tank contains only saturated liquid at 100 psia. Determine (a) the mass of the refrigerant that entered the tank, (b) the amount of heat transfer with the surroundings at 708F, and (c) the entropy generated during this process.
Air at 17 oC is compressed steadily in an adiabatic compressor from 100 kPa to 680 kPa. If the minimum power consumption of this compressor is 7 kW, determine the mass flow rate to run the compressor considering the variation of specific heats with temperature. Note: Do NOT perform interpolation, take the closest value.
A 200-m3 rigid tank initially contains atmospheric air at 100 kPa and 300 K and is to be used as a storage vessel for compressed air at 1 MPa and 300 K. Compressed air is to be supplied by a compressor that takes in atmospheric air at P0 = 100 kPa and T0 = 300 K. Determine the minimum work requirement for this process.
Determine the power produced by an adiabatic turbine if steam enters at 2 MPaa and 400 °C and leaves at a pressure of 6 kPaa. What is the quality of steam leaving the turbine? The mass flow rate of steam is 15 kg. Solve using steam tables
The fluid is heated from 125 degrees Fahrenheit to 225 degrees Fahrenheit. Consider an ideal gas with thefollowing characteristics: R = 85 ft-lbf/lbm-RCp = 0.35 + 0.000325T BTU/lbm-R If the heating is at constant volume, compute for (a) the change in internal energy, (b) the change in enthalpy,and (c) the change in entropy. If the heating is at constant pressure, compute for (d) the change in entropy, and (e) the value of k at 160 degrees Celsius. If the fluid undergoes an isentropic process, determine (f) non-flow work and (g) steady-flow work. (For item f and g, use the value of k at 160 degrees Celsius)
Nitrogen gas is compressed from 80 kPa and 27°C to 480 kPa by a 10-kW compressor. Determine the mass flow rate of nitrogen through the compressor, assuming the compression process to be ideal two-stage polytropic with n = 1.3.
Find the work needed to isothermally compress 150 m3/min of air from 100 kPa to 500 kPa.
An insulated rigid tank of 0. 3 m3 is to be filled with steam by connecting it to a high-pressure steam line at 1400 kPa and 300 ºC. Determine the final temperature of the steam if initially (i) the tank is empty (ii) the tank contains saturated vapor at 350 kPa. ( This problem requires trial and error solution. Please show at least 2 trials even if you do not get the right answer).