Beam ABCDE is subjected to concentrated loads at C and D. A & E are fixed supported and B is roller supported (AB=9m,BC%3D6m,CD3D6M,DE%3D6M). 100KN concentrated load is acting at C and D. The span AB has a moment of inertia which is 1/2 of the moment of inertia of span BE. E is constant (use moment distribution method 1cycle) Solve moment at A

Beam ABCDE is subjected to concentrated loads at C and D. A & E are fixed supported and B is roller supported (AB=9m,BC%3D6m,CD3D6M,DE%3D6M). 100KN concentrated load is acting at C and D. The span AB has a moment of inertia which is 1/2 of the moment of inertia of span BE. E is constant (use moment distribution method 1cycle) Solve moment at A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Ana ly ze the sta tic a lly in d e term in a te b e am d is trib u tio n me th od. Draw shear and bending -moment diagram s. Sketch o f th e de fo rm e d structu re not needed. shown by the moment- 12 ft 28 ft w A B 3 lc 2 lc 3 lc -> 40 ft 20 ft 4 0 ft P(k) w (k/ft) 43.8 3.0
T- B The overhang beam shown is supported by a pin at point A and roller at point 8. The beam is subjected to a uniformly-distributed load w, as shown. Which of the following best describes the shape of the internal shear (M) diagram between points B and C? O a) Cubic O b) Parabolic OC) Linear Od) Constant (non-zero) ) Zero
Ana ly ze the sta tic a lly in d e te rm in a te be am shown by the d is trib u tio n m e th od. D raw shear and bending -moment diagrams. Ske tch of th e de fo rm e d structure notneeded. moment- P 12 ft 28 ft A A В 3 lc 2 lc 3 lc 40 ft 20 ft 4 0ft P(k) w (k/ft) 43.8 3.0
A bridge girder AB on a simple span oflength L =14 m supports a distributed load of maximumintensity q at mid-span and minimum intensityq/2 at supports A and B that includes the weight ofthe girder (see figure). The girder is constructed ofthree plates welded to form the cross section shown.Determine the maximum permissible load q basedupon (a) an allowable bending stress σallow =110 MPaand (b) an allowable shear stress τallow = 50 MPa.
Find the maximum unicormly distributed Ibad (1w) the beam can carry stress are iF He alloable bending and horizontal shearing . GO MPa respectively. Given below is the beam crocs-scction.O 10mm 100 mm 20mm
*4-76. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 50°F, determine the average normal stress in each member when T, = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in?. %3D B C. - 3 ft 2 ft
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G,A=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x104mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vD 2. The normal strain in member AD, CAD 3. The average stress experienced by pin A, TA 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.
A plane frame structure is shown as following figure El=1. Assuming that the inflection points are located at the middle height of the columns and the columns have the same lateral stiffness on each floor. Try to determine the beam end bending moments MA2 of beam A2B2 A₂ El-S By El-3 C₂ El=5 D₂ (55KN) Ele EL El hy 4m El=5 B₂ F₁- El-3C₂ EL-5 D (40KN) hy Sm EL El A₂ EL 4₂₁ B₁ Ele El D₁