beam, For a pre-tensioned Young's Modulus of steel and concrete are 200 GPa and 35.35 GPa, respectively If the ultimate shrinkage strain and Ultimate Creep Coefficient are 200 microns and 1.6, respectively, what the level of sustained stress in concrete at the level of 'steel' if the loss due to creep is three times the loss due to shrinkage.

beam, For a pre-tensioned Young's Modulus of steel and concrete are 200 GPa and 35.35 GPa, respectively If the ultimate shrinkage strain and Ultimate Creep Coefficient are 200 microns and 1.6, respectively, what the level of sustained stress in concrete at the level of 'steel' if the loss due to creep is three times the loss due to shrinkage.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. A split-tension test was conducted on a concrete cylinder with a 150 mm diameter and 300 mm length. Theload that split the cylinder is 268.5 KN. Calculate the splitting tensile strength (fct) of the concrete. b.The third-point flexural strength test was conducted on a flexural beam of 150 mm by 150 mm cross sectionand 450mm span. The maximum load at failure was 29.2 KN. Calculate the flexural strength of the conc c. The ultimate tensile strength of geogrid is 270 KN/m, and the combined reduction factor for reinforcementapplication is 3.0. Determine the allowable tensile strength. d.A compacted sample of Asphalt cement contains 5.3% asphalt binder by weight of total mix, and its bulkspecific gravity is 2.428. The theoretical maximum specific gravity of the mix is 2.592, and the bulk specificgravity of the aggregate is 2.703. Determine the VMA, VTM and VFA of the Asphalt Ce
Given the following properties of beam: b = 250 mm d = 325 mm h = 400 mm a) Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the beam at M = 150 kN-m b) Determine the cracking moment for the section if f'c = 28 MPa c) Compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M = 150 kN-m, n = 8, and reinforced with 4-16 mm diameter tension bars. NOTE: Please answer the question correctly, if you are not sure about the answer(s) please skip the question. Please box the final answer(s) Thank you
Calculate the cracking moment (max. resisting moment) for the unreinforced concrete beam shown. Assume normal-weight concrete with f’c=3,000 psi. Use the internal couple method and check with the flexure formula.
Determine the cracking moment Mcr for the beam depicted in Fig. 6.85. Assume normal-weight concrete, and Grade 60 reinforcing bars. Calculate the bending stresses in the extreme fibers of the cross-section for a service-load bending moment of 90 ft kips.
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.
USE NSCP 2010 A reinforced rectangular concrete beam has a width of 250 mm and aneffective depth of 360 mm. It is reinforced for tension only at the bottomwith a total tension steel area of 600 mm². fc’ = 40 MPa, fy = 400 MPa. a. Determine the tension reinforcement index for this beam.b. Determine the distance of the neutral axis below the compressionsurface. c. Determine the ultimate flexural strength of the beam.
What is the value of the Whitney stress block parameter, β1β1, for 6000 psi concrete?
The design engineer specifies a concrete strength of 31.0 MPa (4500 psi). Determine the required average compressive strength for:a. a new plant for which s is unknownb. a plant for which s = 3.6 MPa (520 psi) for 17 test resultsc. a plant with extensive history of producing concrete with s = 2.4 MPa (350 psi)d. a plant with extensive history of producing concrete with s = 3.8 MPa (550 psi)
What is the cracking moment of a H=400mm by W=300mm beam if the specified compression strength of the normal weight concrete (f'c) used is 30MPa? your answer must be in kNm form.
A group of concrete cubes mixed with different water ratios .. The group with water ratio W / c = 0.3The maximum load was testedFailure causes every cube in the group Required:1- Finding the stress rate for each group in unit N / mm2 with discussing the results and the effect of the water w / c ratio on the compressive strength of the group.
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
A normal-weight plain concrete beam is 6 in. x 12 in. is simply supported on a span of 4 ft and is subjected to a midspan concentrated load of 4500 lb. Assume f’c = 3,000 psi, and concrete unit weight is 150 lb/cf. Calculate the maximum concrete tensile stress using both methods, and compare it with the value for modulus of rupture (fr) using the ACIrecommended value based on f’c.