Because of the additional equipment installed, it requires an additional flowrate of 800 CFM. The air handling unit has a 7.5 hp motor and produces 2" of static pressure. The fan produces 8,000 cfm of air at 1500 rpm. The original design specifications however for the air handling unit has only 5.5 hp of the motor being used and plans to use the same motor, just to increase the power. What is the additional static pressure that will be available to the system? SP₂ Asp BHP 2 N₂ in. in. hp mקיר

Because of the additional equipment installed, it requires an additional flowrate of 800 CFM. The air handling unit has a 7.5 hp motor and produces 2" of static pressure. The fan produces 8,000 cfm of air at 1500 rpm. The original design specifications however for the air handling unit has only 5.5 hp of the motor being used and plans to use the same motor, just to increase the power. What is the additional static pressure that will be available to the system? SP₂ Asp BHP 2 N₂ in. in. hp mקיר

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter26: Applications Of Refrigeration Systems

Section: Chapter Questions

Problem 9RQ: Three disadvantages of parallel compressor systems are _____, _____, and ____.

See similar textbooks

Similar questions

To supply combustion air, a forced draft fan requires 1975 rpm at 4.8 lb-ft. What horse power rating is required for the electric motor driver?
A pneumatic motor for a torque gun requires 8 CFM at 110 psi to operate. What minimum SCFM flow rate is required into the compressor to run this tool?
25.a. A two-stage compressor with a capacity of 1000 dm compresses 100 cu ft of free air per minute to apressure of 100 psi. What is the required bhp?A. 4B. 14C. 8D. 18 25.b. A centrifugal fan running at 100 rpm delivers air at the rate of 6000 dm at a pressure of 1 oz per sq in.and requires 2 hp. At 300 rpm it delivers 18,000 cu ft of air per minute. What is the horsepower required?End of examA. 27B. 54C. 9D. 18
A HAWT is installed at a location having free wind velocity of 15m/s. The 80 mt diameterrotor has three blades attached to the hub. Find the rotational speed of the turbine foroptimal energy extraction
A 35MW generator is to operate by a double overhung Pelton wheel. The effective head is 350m at the base of the nozzle. Find the size of jet, mean diameter of the runner and specific speed of wheel. Assume Pelton wheel efficiency 84%, velocity coefficient of nozzle 0.96, jet ratio 12, and speed ratio 0.45 Show schematic diagram and provide solutions.
An air conditioning supply fan is operating at and requiring 4.85kW. 600 RPM against is delivering 540m / min at 500PA SP It standard conditions. In order to handle air conditioning load, heavier than originally planned, more air is desired, in order speed SP and to increase flow are the new power?
When using a double acting pressure intensifier for continuous pressure increase, we are looking to have pressure intensified brand operate at 5L/min at 30 MPA. If the main pump can supply 10L/min at 10 MPA, what is the diameter ratio needed between actuator and boosting piston?
centrifugal compressor has pressure ratio of 4:1 with an isentropic efficiency of 80% when running at 15000 rpm and inducting air of 293° K. Curved vanes at inlet given the air a pre whirl of 25° to the axial direction curved vanes at inlet given the air a pre whirl of 25° to the axial direction at all radil and mean dia of eye is 250 mm. The absolute air velocity at inlet is 150 m/sec. Impellér tip dla 600 mm calculate slip
A single-stage, single-acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1.26. The induced volume flow rate is 7.2 cubic meters per min and the air must be delivered at a pressure of 697 kPa. The free air conditions are 101.3 kPa and 16 degrees Celsius. The clearance volume is 6% of the stroke volume and the stroke/bore ratio is 1.6/1. Calculate the delivery air temperature in degree Celcius to one decimal place.
axial flow compressor of 50% reaction, blading has isentropic efficiency of 82%. It draws air at 17 °C and compresses in the pressure ratio of 4:1. The mean blade speed and flow velocity are constant through out the compressor. The inlet and outlet angles of blades are 15° and 45° respectively from axial direction. Blade speed = 180 m/sec work input factor, 2=0.84. Calculate (i) flow velocity (il) no. of stages.
Air Is To Be Compressed In A Single-Stage Reciprocating Compressor From 1.013 bar And 15°C To 7 bar.For A Free Air Delivery Of 0.3 meter cubed per min.The Compressor Is To Run At 1000 rev/min.If The Compressor Is Single-Acting And Has A Stroke/Bore Ratio Of 1.2/1, Calculate The Bore Size Required.
what is the types of industrial compressors, write summary and work mehod of each type?