Below is a stress element in an alumina (Al2O3) beam with a £f<0.05. ox = 0.2 GPa, oy = 0.3 GPa in the negative y direction, and Txy = 0.1 GPa. The strength of the beam is Sut = 0.25 GPa, and Suc = 2.95 GPa. Find the factor of safety of the stress element using a the Brittle Coulomb Mohr theory. ↑ N Txx X

Below is a stress element in an alumina (Al2O3) beam with a £f<0.05. ox = 0.2 GPa, oy = 0.3 GPa in the negative y direction, and Txy = 0.1 GPa. The strength of the beam is Sut = 0.25 GPa, and Suc = 2.95 GPa. Find the factor of safety of the stress element using a the Brittle Coulomb Mohr theory. ↑ N Txx X

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.8P: A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a...

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a uniform load (see figure). The beam has a length L = 27.5 m and rectangular cross section of a width b = 4.0 m and thickness t = 0.88 m. The total load on the beam is 17.2 N. If the deflection at the end of the beam is 2.46 m is what is the modulus of elasticity Egof the gold alloy? (Use the formulas of Example 9-2.)
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
Solve the preceding problem for a column with e = 0.20 in,, L = 12 ft, I = 2L7in4, and E = 30 × 106psi.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A materila has a modulus of elasticity (E=17 Mpa) and a poissons ratio of 0.27. what is the approximate value of the shear modulus, G?
</o:p> A material is known to have a fully modified endurance strength of 60 kpsi, a yield strength of 120 kpsi, and an ultimate tensile strength of 150 kpsi. A beam made of this material subject to repeated bending stress that goes from 0 psi to 110 kpsi. Using Gerber as our failure criterion </o:p> a. Does the beam have infinite life? </o:p> b. What is the equivalent fully-reversed stress? </o:p> c. How many cycles do we expect this beam to last?</o:p> </o:p>
A solid circular cross-section beam with length, L is subjected to a pure torsion T = 0.5 F(Nm) and a tensile load P = 5F N. Find the maximum value of F that can be applied to thebeam with a safety factor of 2.5 using;i) Maximum shear stress theoryii) Shear/distortion energy theory(Beam is made of steel with a diameter of 50 mm, L= 1.5 m, E = 200 GPa, Y = 250 MPa, v =0.29)
A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 3.75w N, (++)Mmax = 2.53w N-m, (−−)Mmax = 4.5w N-m. From the given cross section shown, ytop = 100mm, ybot = 150mm, and INA = 72.92 x 10 6 mm4. The allowable stresses are as follows: σfT = 40 MPa, σfC = 70 MPa, and τ = 10 MPa. (a) The safe uniform load considering tensile flexural stress is _____ N/m. (b) The safe uniform load considering compressive flexural stress is _____ N/m. (c) The moment of the area about the neutral axis is _____ mm3. (d) The safe uniform load considering maximum shear force is _____ N/m. (e) Based on your analysis, the safe uniform load to recommend is _____ N/m