Answered: Q 4 For the figure below, the average…

Q 4 For the figure below, the average shearing stress in each rivet is ..kPa (Hint: Two 22-mm-diameter rivets resist this force) 45 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Related questions

Q: A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in…

A: To Find: The torque that can be applied. Given : The outside diameter is Do=300 mm. The diameter of…

Q: The ultimate shearing stress of the plate is , = 300 MPa The compressive stress in the punch is o̟ =…

A: The ultimate shear stress for the plate is given as 300 MPa; the thickness of the plate is given as…

Q: A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 261 mm in…

A: Given data as per the question 4 d-mm bolt on concentric bolt circle 194 mm in diameterT=8728…

Q: 4. From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.35°.…

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

Q: 5. The position of the rod DE is controlled by the hydraulic cylinder CF. For example, if the…

A: Given Load, P = 400 lb Bending stress = 15 ksi Diameter, d = 1/4 inch = 0.25 inch…

Q: 5. The position of the rod DE is controlled by the hydraulic cylinder CF. For example, if the…

A: Given Load, P = 400 lb Bending stress = 15 ksi Diameter, d = 1/4 inch = 0.25 inch…

Q: The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of…

Q: 4. Write the relations used for maximum stress when a machine member is subjected to tensile or con…

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A: Solution: Maximum shear stress is given by, Solid tube,…

Q: The lap joint shown in fig. Is fastened by FOUR 20-mm diameter rivets. Assuming that p = 50 kN,…

Q: In the figure, a double shear occurs at 20mm diameter pin at B, what is the shearing stress? In…

Q: Q5/ If the No.of rivets wanted to joint two plates type Double cover Butt joint is 40 as shown in…

Q: Two plates 20 mm thickness are fastened by a number of 25 mm diameter rivets, a tensile load of 500…

Q: " A thick steel cylinder which has an inside diameter of 1m is subjected to an internal pressure of…

Q: A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 268 mm in…

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

Q: For the figure below, the average shearing stress in each rivet is .kPa (Hint: Two 22-mm-diameter…

Q: Home Work: 1. As shown in figure below, a hole is to be punched out of a plate having an ultimate…

Q: (b) A solid rectangular shaft of cross-section 80 mm × 50 mm is welded by a 5 mm fillet weld on all…

A: Given data L=80 mmb=50 mmt=5 mmτ=85 N/mm2

Q: Q1: Calculate the thickness of a triple riveted lap joint, if the rivet diameter of five plates is 5…

Q: find the smallest diameter bolt that can be used in the clevis P=400KN shearing strength of the…

Q: Q4. If you have a rod with an initial cross-sectional area of 10 mm, final cross- sectional area is…

A: Given Force, F = 500 N Yield stress = 300 MPa Find Drawing stress

Q: For the pin-connected structure in the figure, determine the minimum diameter for the pin at joint D…

Q: Q 3: The smallest diameter bolt that can be used in the clevis shown in .figure is.. if P= 200 kN.…

A: Given, Applied force = P = 200 kN = 2 x 105 N Shear strength of bolt = τ = 300 MPa Let us say…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: A torque of 2.5 kN.m is applied to the hollow, thin- walled, aluminium section shown in Fig. 3.18.…

A: As illustrated in the picture in the question, a torque of 2.5 kN.m is given to the hollow,…

Q: A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 262 mm in…

A: Answer: The diameter of the bolt is 12.55 mm.

Q: A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet…

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

A: GIVEN: WORKING SHEAR STRESS, τ= 64MPa diameter of disc A=250mm diameter of disc B=500mm diameter of…

Q: Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking…

A: The shearing force is given by, Fshear=0.7×σu×T×L where, T = sheet thickness = 2.5 mm L = total…

Q: Calculate the blank size of the figure shown and locate bending lines: The thickness of the sheet t…

Q: a clevis acted upon by force P. If the maximum shearing stress is 15ksi, determine the minimum bolt…

Q: The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of…

Q: lues of shearing stress at (1) point a, (2) point b. 100 జ 180 kN 20 mm 100 mm 30 mm Figure 3 500 mm…

Q: A coupling is used to connect a 51mm diameter plastic rod to a 35mm diameter rod as shown. If the…

Q: horizontal shearing stress?

A: Using shearing stress of beam formula we have calculated. detailed solution given below

Q: Given the figure with its V = 45 kN; bf = 9: mm; bw = 20 mm; d = 115 mm; tf = 28. What is the…

Q: The lap joint shown in the figure is fastened by four 10- mm diameter rivets. Assuming that F= 71KN,…

Q: The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that P = 200KN, determine (a)…

Q: A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 267 mm in…

Q: A W310 x 52 beam is made with a material that has a maximum shearing stress of 90MPa. Determine the…

A: As Given in Question:- Shearing Force = 90 Mpa W310*52 depth from table = 318 mm Area for this =…

Q: P Find the smallest diameter bolt that can be used in the clevis in Fig. if P = 435 kN. The shearing…

Q: 4. Write the relations used for maximum stress when a machine member is subjected to tensile or com-…

A: Let a machine member is loaded with tensile stress and shear stress.

Q: A 5 hp engine is transmitting power to a generator at 1800 rpm through a steel shaft. Determine the…

Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…

Q: A plate is fastened to a fixed member by four 20-mm-diameter rivets arranged as shown in Fig. P-333.…

A: Given data Diameter of rivets = 20 mm Force = 14 kN

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Q 4 For the figure below, the average
shearing stress in each rivet is ..kPa (Hint:
Two 22-mm-diameter rivets resist this
force)
45 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
write legibly Indicate all necessary FBDs, concepts and formulas needed in the solution. The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that P = 200KN, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6 rivets, and the diameter of hole is 22mm. See figure 102.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
A lever, secured to a 2 inches round shaft by a steel tapered pin (d = 10 mm), has a pull of210 N at a radius of 810 mm. Find S, the working stress on the pin, in Mpa. Consider doubleshear on the pin.
Two circular rods of 50mm diameter are connected by a knuckle joint, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin.
The lap joint shown in the figure is fastened by three 20mm diameter rivets. Find the largest value of P if the allowable shearing stress, bearing stress and average tensile stress are 55 MPa, 32 MPa and 20 MPa
In the given figure below what is the normal and shear stresses in MPa at point P?
Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA
A lap joint shown is made by two identical plates that are connected by nine 15-mm diameter rivets. The diameter of each hole is 18 mm. Assume that the force P is equally distributed among the rivets. (t = 20mm) A. What is the maximum force in Newton if the shear stress of the rivets is limited to 5 MPa and the bearing stress between each rivet and a plate is 6 MPa? B. If the force P-20 KN, what is the tensile stress in MPa at section a-a of the top plate?
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?