Box BeamBox BeamSupport at AabCa = 1.7 ft, b = 3.4 ft, and c = 2.55 ft.P = 3300 lbdiameter of pin A=0.820 in.box beam wall thickness, t = 0.410 in.What is the average bearing stress in the box beam at A? Answer in ksi rounded-off to 2decimal placesPinABCD

Answered: Image /qna-images/answer/a24cde53-3904-4562-8124-86aff2fc23d7.jpg

Box Beam Box Beam Support at A a b с a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3300 lb box beam wall thickness, t = 0.410 in. diameter of pin A=0.820 in. What is the average bearing stress in the box beam at A? Answer in ksi rounded-off to 2 decimal places Pin P↓ с B D

Box Beam Box Beam Support at A a b с a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3300 lb box beam wall thickness, t = 0.410 in. diameter of pin A=0.820 in. What is the average bearing stress in the box beam at A? Answer in ksi rounded-off to 2 decimal places Pin P↓ с B D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.10.6P: An overhanging beam ABC with a rectangular cross section has the dimensions shown in the figure. A...

See similar textbooks

Related questions

Q: ornal aBi=k(-200cessed), 3- If the acceleration of point G is ag = (-261-45.0)) m/s2, determine the…

A: To find: The vertical reaction at point C, Cy = ?

Q: In the Figure 6, the reaction force in the y- direction at point B is (in kN): Figure 6: y 5 m 5 m A…

Q: 20. An abstract says: "This paper develops a system dynamics model of Iceland's energy sector…

A: option c statistical design

Q: What properties does an involute have? Please answer this based on the notations in the figure.

A: Although a variety of profiles can be employed to create gears, the involute curve is the most…

Q: Questions 17-20 According to the truss shown in figure, answer the following questions: 17.The force…

A: Q.18 Given: 3 KN horizontal force at joint H And 4 kN force at joint G and F vertically downward.…

Q: Write the equation of motion of the system shown in figure in matrix form. my IT ₂8 ₂ Fi(t) x1(1) m₂…

Q: Assuming that adding 5-cm of insulation drops the U-value of a building from 1.36 to 0.556 W/m2- °C,…

Q: Q3: In a mechanical application a composite part is required to have the properties, the…

A: Given Data The longitudinal modulus of elasticity is:Ec1required=105 GPa The transverse modulus of…

Q: 7. Cross and Dot Product and Resultant Distinctions Two forces act on an object A with an alignment…

Q: In the Figure 5, if the Young modulus is 20 Gpa, the strain percentage in the direction the normal…

A: To find strain percentage

Q: Q.5) Three forces are applied to bracket as shown in figure below. Replace the given force system by…

A: A0,120,0B70,120,40C70,120,-40D110,0,0E150,-50,100

Q: The B Dynamics Squad is at it again with more experiments. Thin disk C weighs Wc = 30 lb, is…

Q: Design for that is, the load can be taken by other members or the effect of fatigue failure…

A: 6) aeroplane 7) high tolerance 8) cause and effect analysis

Q: normal aBi=k(-200cesso - If the acceleration of point G is ag = (-261-45.0)) m/s2, determine the…

A: Given Mass, m = 7.5 kg Angular velocity = 18 rad/s Find Force exerted, F

Q: Find the value of angle 0 if the resultant is vertical. Also, find the magnitude of the resultant. Y…

Q: Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the…

A: The calculated angular velocity with which the right propeller ends up after both propellers have…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: P = 400 KN X…

Q: For the beam shown in the figure if W- 14 KN/m. Determine the following: 14. The normal force at…

A: (14)

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: as per guideline i have to solve only first question

Q: According to the Figure 2, if P = 60 N and R = 100 N, then 8 should be: Figure 2: Ꮎ R B α T…

Q: 1- The fluid with constant density is called an: a. Ideal fluid b. compressible fluid c.…

A: Ideal fluid is incompressible and non-viscous . Real fluid is compressible and viscous and has shear…

Q: ater flows through a horizontal coil heated from the outside by high temperature flue gases. As it…

A: given

Q: A disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0…

A: Given Radius, r = 1 m Angular velocity = 2 rad/s Find Magnitude of acceleration

Q: ..A 6.8-liter, in-line, eight-cylinder Cl engine has a compression ratio rc=18.5 and a crevice…

Q: In an engine working on an ideal Otto cycle, the temperatures at the beginning & at the end of…

A: Otto cycle is a constant volume heat addition cycle which consists of four processes:- Isentropic…

Q: 24. Which test of validity can confirm to predicted correlations with other theoretical…

Q: How does a fin enhance heat transfer at a surface?

A: Fins are the projections or extended surfaces protruding from hot surface into ambient fluid and…

Q: * Calculate the reactions at point A of the three forces shown in ?figure 50 N 100 N 3 3mm 2mm 5mm…

Q: 1. During a ground test with both main and tail rotors in steady operation, a 400 N aerodynamic…

A: Given Force, F = 400 N Distance, d = 6 m Find Force couple system, C

Q: Find the duty of this heat exhanger when new: Q6: Say we have a heat exchanger made to heat 150…

Q: During a wall heat flux measurement, at the instantaneous time t, we obtained the following values:…

Q: Shown in the figure is a 258-kg homogeneous cylinder that slipping on the rolls without horizontal…

A: Equations 1 and 2 are Newton's 2nd law of motion for rotation and translation respectively.

Q: af i= Cro fin 3- If the acceleration of point G is ag = (-261-45.0)) m/s2, determine the absolute…

A: To find: vertical reaction acting at point C, Cy = ? N.

Q: Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of 200…

A: Given:At=1150 mm2σf=200 MPaFf=78600 Nεt=1.56*10-3σm=6.18 MPa

Q: ose that a power plant operates on a Carnot vapor cycle and uses water as the working substance.…

A: Given:P1=10 MPaP2=20 KPa

Q: Problem Determine the mass moments of inertia (in slug-ft²) and the radii of gyration of the steel…

Q: disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0…

Q: Does a scramjet engine have better efficiency than a ramjet engine for hypersonic flights? Why?

A: To find: Lets us determine the reason for scramjet engine have better efficiency than a ramjet…

Q: Q2/ How will the following increase efficiency of the LC. engine? 1. Mixing some of exhaust gases…

A: Given question: How will the following increase efficiency of the IC engine? 1. Mixing some of…

Q: a. principle of replication b. principle of randomization neip C. d. principle of local control both…

A: option d is correct principle of randomization principle of local control

Q: In the Figure 5, if the Young modulus is 200 Gpa, the strain percentage in the direction of the…

Q: Calculate thermodynamic and isentropic efficiency of a turbine: Mass flow rate 5kg/s = Condenser…

Q: Q2/ How will the following increase efficiency of the I.C. engine? 4. Movement of the piston to pass…

A: Given question: How will the following increase efficiency of the IC engine? 4. Movement of the…

Q: Q1: E-glass fibers reinforced epoxy matrix to fabricate a composite part. The volume fraction of…

Q: A ball is dropped from the top of a tower 80 ft high at the same instant that a second ball is…

Q: Q3: In a mechanical application a composite part is required to have the properties, the…

A: Given Data The longitudinal modulus of elasticity is:Ec1required=105 GPa The transverse modulus of…

Q: The radius of the wheel is r=3 m. The tangential acceleration of the point on the edge of the wheel,…

Q: The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk…

A: Solution - Given data -M =4.9 kgKo =230 mmm =0.17 kgN1 =164 rev/min

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

Q: The machine is being designed to carry out a pressing operation, as part of this a dual flywheel…

A: Answer: (a) Initial kinetic energy = 4875 Joule (b) Final kinetic energy = 4602.3 Joule (c) Energy…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Box Beam
Box Beam
Support at A
a
b
C
a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft.
P = 3300 lb
diameter of pin A=0.820 in.
box beam wall thickness, t = 0.410 in.
What is the average bearing stress in the box beam at A? Answer in ksi rounded-off to 2
decimal places
Pin
A
B
C
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for a column with e = 0.20 in,, L = 12 ft, I = 2L7in4, and E = 30 × 106psi.
-5 Calen1ate the deflections S 3a nd
A weight W = 4000 lb falls through a height h = 0.5 in, onto the midpoint of a simple beam of length L = 10 ft (see figure). Assuming that the allowable bending stress in the beam is = 18,000 psi and E = 30 x 10* psi, select the lightest wide-flange beam listed in Table F-l(a) in Appendix F that will be satisfactory.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A square wood column with side dimensions b (see figure) is constructed of a structural grade of southern pine for which Fc= 10,5 MPa and E = 12 GPa. An axial force P = 200 kN acts on the column. If the dimension b = 150 mm, what is the maximum allowable lensth Lmax, of the column? If the length L = 4.0 m, what is the minimum required dimension bmin?
A pontoon bridge (see figure) is constructed of two longitudinal wood beams, known as bulks, that span between adjacent pontoons and support the transverse floor beams, which arc called chesses. For purposes of design, assume that a uniform floor load of 7.5 kPa acts over the chesses. (This load includes an allowance for the weights of the chesses and balks.) Also, assume that the chesses are 2.5 m long and that the balks are simply supported with a span of 3.0 m. The allowable bending stress in the wood is 15 MPa. If the balks have a square cross section, what is their minimum required width b^l Repeat part (a) if the balk width is 1.5 b and the balk depth is b; compare the cross-sectional areas of the two designs.
A weight W = 20 kN falls through a height h = 1,0 mm onto the midpoint or a simple beam of length L = 3 m (see figure). The beam is made of wood with square cross section (dimension don each side) and E = 12 GPa. If the allowable bending stress in the wood is °aLLow =10MPa, what is the minimum required dimension
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
A hollow box beam with height h = 16 in,, width h = 8 in,, and constant wall thickness r = 0.75 LiL is shown in the figure. The beam is constructed of steel with yield stress ty = 32 ksi. Determine the yield moment My, plastic moment A/p, and shape factor.
An overhanging beam ABC with a rectangular cross section has the dimensions shown in the figure. A weight W = 750 N drops onto end C of the beam. If the allowable normal stress in bending is 45 MPa, what is the maximum height h from which the weight may be dropped? (Assume E = 12 G Pa,)
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
Solve the preceding problem for a wide-flange beam with h = 404 mm, b = 140 mm, bf= 11.2 mm, and rf. = 6.99 mm.