Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in parallel and operating at a voltage of 13.2 kVms. The local utility supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Mall 1 is consuming 400 kW at 0.75 pf lagging while Mall 2 is consuming 300 KVAR at 0.80 pf lagging. Determine the following: a) The local utility's sending-end (source) voltage. b) The total real and reactive power of the system. c) The overall pf of the system.

Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in parallel and operating at a voltage of 13.2 kVms. The local utility supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Mall 1 is consuming 400 kW at 0.75 pf lagging while Mall 2 is consuming 300 KVAR at 0.80 pf lagging. Determine the following: a) The local utility's sending-end (source) voltage. b) The total real and reactive power of the system. c) The overall pf of the system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.43P: A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads...

See similar textbooks

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry anadditional load of 170 kW at 0.85 pf lagging. With the mentioned power factor, thesubstation is experiencing inefficient electrical system: high power losses, high voltagedrops in the electrical equipment, and high electricity bill. To reduce power losses and toreduce the electricity bill, power factor correction is to be of high importance andconsideration. With this condition, the substation is considering of two alternatives namely:Alternative A: To increase the capacity of the substationAlternative B: To add shunt power capacitor In this regard, the owner requested to prepare a summary report consisting of thefollowing details: additional substation capacity in kVA
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional load of 170 kW at 0.85 pf lagging. With the mentioned power factor, the substation is experiencing inefficient electrical system: high power losses, high voltage drops in the electrical equipment, and high electricity bill. To reduce power losses and to reduce the electricity bill, power factor correction is to be of high importance and consideration. With this condition, the substation is considering of two alternatives namely: Alternative A: To increase the capacity of the substation Alternative B: To add shunt power capacitor In this regard, the owner requested to prepare a summary report consisting of the following details: 1. A rightful power phasor diagram.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
Discuss the concept of microgrids and their potential benefits for localized power distribution.
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?