By using virtual work find the moment 'T' to keep the system in equilibrium. M=(15+n) kg, 0 = 40°. Bar BC always stays in the horizontal position. Use 'n' = question number. Write the solution step by step. Make sure to present your solutions clearly and legibly. (Example: If question number is 2, n=2) A 0.3 m B 0.1 m M 0.2 m C

By using virtual work find the moment 'T' to keep the system in equilibrium. M=(15+n) kg, 0 = 40°. Bar BC always stays in the horizontal position. Use 'n' = question number. Write the solution step by step. Make sure to present your solutions clearly and legibly. (Example: If question number is 2, n=2) A 0.3 m B 0.1 m M 0.2 m C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

Q 40/A homogeneous bar of length / and weight w lb rests horizontally as shown in Fig. 40 with its free endon a block of weight W. the block W is at rest on a plane inclined at the angle a with the horizontal. Determine the necessary coefficient of friction u between the block and the plane for equilibrium. Assume no friction between the bar and the block.
Q)Two blocks A=150 N and B=? are connected by a rod at their ends by frictionless hinges as shown in the Fig. Find the weight of block B required for limiting equilibrium of the system, if µ = 0.35 at all sliding surfaces.
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work. These are my answers FBD=2F, RAX=353.5N RAy= 353.5N but am not sure if a correct any help
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work.
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
A metal rod of length L=8.88 has only three forces applied to it in the directions shown in the diagram below. Force #2 is applied at the midpoint of the rod. If the rod is in static equilibrium and the magnitude of force #1 is 7.15, what is the magnitude of force #2?
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
In the diagram, Force F must pull with 30N to keep the system in static equilibrium, what is the weight? If the diameter of Gears D and G were changed to 14 cm, what would the required force to hold thesystem in equilibrium be? (Use the weight calculated previously)
Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 = 4.65 KN W1 = 6.15 KN/m Unknowns : RAy , RAx ,RBy , MA What is the value of internal shear 2.50m to the right of support A
A) Imagine a procedure used for the execution of a certain work, as shown in the following figure. Such a crane has a mass of 1000 kg and is transporting a coffin with a total mass of 2400 kg. Assume that support A is fixed, support B is movable, and point G is the center of gravity of the lift. What are the support responses in kN? Question 1 options: a) The support responses are as follows: Rax = Rbx = 34 kN and Ray = 109.33 kN. b) The supporting responses are as follows: Rax = Ray = 109.33 kN and Rbx = 34 kN. c) The support responses are as follows: Rax = 56.8 kN; Rbx = 109.33 kN and Radius = 34 kN. d) The support responses are as follows: Rax = 156.7 kN; Rbx = 89.65 kN and Radius = 34 kN. e) The supporting responses are as follows: Rax = Rbx = 109.33 kN and Ray = 34 kN. B. Consider the beam shown in the following figure. In this beam, there are different types of existing forces, such as applied moment, distributed load and point load. Knowing the magnitude of each of the forces,…
When F = 300 N with Θ = 40°, what is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads.
The rod AB is held in equilibrium by a vertical wall, the horizontal floor and by a cable CB. Assuming there is no friction, derive all the external forces acting on the rod. Then assuming there is friction at the wall and floor with a static coefficient of 0.3 and assuming that the rod is under impending motion conditions, derive all the external forces acting on the rod. The rod AB is 1m long and has a weight of 205N, the angle between AB and the cable CB is 15 degrees and the angle between the cable CB and the floor is 30 degrees.