c) A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a length of 500 mm and a diameter of 10 mm. Compute the magnitude of the load required to produce a 2.5 x 103 mm change in length if the defomation is entirely elastic. The elastic modulus of brass is 97 GPa.

c) A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a length of 500 mm and a diameter of 10 mm. Compute the magnitude of the load required to produce a 2.5 x 103 mm change in length if the defomation is entirely elastic. The elastic modulus of brass is 97 GPa.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 54PQ

See similar textbooks

Similar questions

Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
(a) Estimate the force with which a karate master strikes a board, assuming the hands speed at the moment of impact is 10.0 m/s and decreases to 1.00 m/s during a 0.002 00-s time interval of contact between the hand and the board. The mass of his hand and arm is 1.00 kg. (b) Estimate the shear stress, assuming this force is exerted on a 1.00-cm-thick pine board that is 10.0 cm wide, (c) If the maximum shear stress a pine board can support before breaking is 3.60 106 N/m2, will the board break?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
Use the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27