c) Describe the force exerted by the oil on the gate d) What does the center of pressure mean? And why is it always located below the centroid of the submerged surfaces? e) Draw a sketch showing the location of the centroid and the center of pressure 1 m SAE 10W-30 Gate 2 m В

c) Describe the force exerted by the oil on the gate d) What does the center of pressure mean? And why is it always located below the centroid of the submerged surfaces? e) Draw a sketch showing the location of the centroid and the center of pressure 1 m SAE 10W-30 Gate 2 m В

Name: c) Describe the force exerted by the oil on the gated) What does the
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: c) Describe the force exerted by the oil on the gated) What does the center of pressure mean? And why is it always located below the centroid of thesubmerged surfaces?e) Draw a sketch showing the location of the centroid and the center of pressure1

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.86P: Determine the volume of the concrete arch dam.

See similar textbooks

Similar questions

As the water level in the retention pond drops(due to evaporation, infiltration, etc) does the location of the hydrostatic resultant force(center of pressure) move closer to the centroid of farther from the centroid? Note : This does not require any math, just an understanding of the yp equation. Options: a. Not enough information b. Farther C. Closer
The base of a rectangular vessel measures 10cm x 18cm. water is poured in to a depth of 4cm , what is the pressure on the base ?. what is the thrust on the base ?.g=10m/s2
In Fig.= both the tank and the tube are open to theatmosphere. If L = 2.13 m, what is the angle of tilt θ of thetube?
How far below the water surface should a vertical square 1.22 m on a side with two sides horizontal, be immersed so that the center of pressure will be 76 mm below the center of gravity?
Find the height of the portion of a cubic block that extends below the water surface (h) , the specific gravities of block and seawater are given to be SG = 0.778 and 1.025, respectively. h1 = 13.1cm
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
11th - A rectangular plate with a width of 2 m and a height of 3 m was submerged in water. The distance of the upper edge of the plate from the free surface of the water is 5 m. Since the atmospheric pressure is 95 kPa, what is the hydrostatic pressure force on the plate surface considering the atmospheric pressure? a) 688 kN B) 747 kN NS) 864 kN D) 307 kN TO) 2950 kN
A piece of cork having a specific weight of 2.36 kN/m is shaped as shown in Fig. 5.32. (a) To what depth will it sink in turpentine (sg = 0.87) if placed in the orientation shown? (b) Is it stable in this position?
Please provide clear written solution and fiqures. Thank you! A block of wood is 15 cm square and 30 cm long. (a) What is the specific gravity of the wood if the metacenter is at the same point as the center of gravity of the wood when the block is floating in water on its side. (b) Would it be stable floating on its end? Explain.
The system in Fig. is at 20 ° C. Determine the heighth of the water in the left side.
Discuss the variations of hydrostatic force with depth of immersion.
A concrete block is attached to the gate as shown. If the water level is 1.3 m from the bottom of the container, there is no reaction force at A.What would be the reaction force for the level shown?Note 1: Specific gravity of concrete is 2.4.Please show clear workings with explanations to steps taken. I don't just want the answer, I want to understand the process to answering this question. Thanks