Consider a steam power plant operating on an ideal Rankine cycle. This steam power cycle can achieve a cycle thermal efficiency of at least 25 percent. i) Decide about the systems' components, working temperature and pressure of this power plant. ii) Illustrate system schematic and T-s diagrams with completely labelled on the systems' components, working temperature and pressure. iii) Evaluate the compatibility between proposed parameters and thermal efficiency of the plant.

Consider a steam power plant operating on an ideal Rankine cycle. This steam power cycle can achieve a cycle thermal efficiency of at least 25 percent. i) Decide about the systems' components, working temperature and pressure of this power plant. ii) Illustrate system schematic and T-s diagrams with completely labelled on the systems' components, working temperature and pressure. iii) Evaluate the compatibility between proposed parameters and thermal efficiency of the plant.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Rankine Engine-Generator unit receives 27,000 kg/hr of steam at 1.2 MPa and 150°C and exhausts to a condenser temperature of 22 C. Brake steam rate is 4.74 kg/kW-hr, mechanical efficiency is 90 % and generator efficiency is 94 %. Determine: a) ideal cycle thermal efficiency, b) indicated engine efficiency, c) generator output (kW), d)the condition of turbine actual exhaust
Perform a parametric study for a steam power plant operating between pressures of 7 MPa and 7 kPa on an ideal Rankine cycle. Use feedwater heater pressure as the variable. Produce plots similar to Figure IIb.2.3 for such parameters as fraction of the steam extraction, pump work, and turbine work.
Thermodynamics: - Clear writing please!!! Thank you - Sketch and label all numbers on the turbine. - Sketch and label all numbers on the process on a T-s diagram. 7.133E A large condenser in a steam power plant dumps 15 000 Btu/s by condensing saturated water vapor at 115 F with an ambient temperature of 77 F. What is the entropy generation rate?
A dual-pressure combined-cycle power plant consists of a gas turbine,HRSG, and steam turbine plant. The gas turbine exhaust gas flow rate is590 kg/s, temperature is 608°C, HP superheated steam condition is 140bars and 550°C temperature, LP saturated steam is at 8 bar, condenserpressure is 0.05 bar, and feedwater temperature is 120°C. Assuming apinch point of 11 K for both high and low pressure, an exhaust gas specific heat of 1.05 kJ/(kg K), and an isentropic efficiency of the steamturbine of 0.9, calculate (a) the total steam production rate of the HRSG inkg/s, (b) the HRSG heat transfer rate in kJ/s, (c) the stack gas temperaturein °C, and (d) the steam turbine power output in kW.
Pls answer thank you! The following data were obtained during performance test with a simple open cycle gas turbine engine: compressor inlet temperature, 520*R: compressor isentropic discharge temperature, 672"R: actual compressor discharge temperature, 691"R: turbine inlet temperature, 1500 R: turbine isentropic discharge temperature. 1184"R: and turbine actual discharge temperature, 1216°R. For these conditions calculate the thermal efficiency in percent.
Discuss the importance of thermodynamics knowledge in the design and analysis of conventional power plants
How to increase a thermal efficiency of Rankine cycle? Explain your answer on T-s diagram Thermodynamics question. Briefly explanation please.
Part C only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve Part C below using the variable specific heat assumption. Part C - Determine the heat input qin in the process 2 → 3, the work wC used by the compressor, and the work wT produced by the turbine per kg of air.
Describe the components of a steam power plant and demonstrate the process of it undergoes.
A single-pressure combined-cycle power plant consisting of a gas turbine, HRSG, and steam turbine plant. The gas turbine exhaust gas flow rate is 600 kg/s, temperature is 600°C, live steam condition is 70 bar/500°C, condenser pressure is 0.04 bar, and feedwater temperature is 140°C. Assuming a pinch point of 12 K for both high and low pressure, an exhaust gas specific heat of 1.05 kJ/(kg K), and an isentropic efficiency of the steam turbine of 0.9, calculate: (a) the rate of steam production in kg/s, (b) the stack gas temperature in °C, (c) the steam turbine power output in MW, and (d) the heat transfer rate in the HRSG in kJ/s.
Hey! This question has already been solved here many times. But I have been asked to solve this question from the Heat Transfer point of view (Heat and Mass Transfer - Incropera - Chapters 7 - 11). Consider a regenerative vapor power cycle with two feedwater heaters, a closed one and an open one. Steam enters the first turbine stage at 8 MPa, 480ºC, and expands to 2 MPa. Some steam is extracted at 2 MPa and fed to the closed feedwater heater. The remainder expands through the second-stage turbine to 0.3 MPa, where an additional amount is extracted and fed into the open feedwater heater, which operates at 0.3 MPa. The steam expanding through the third-stage turbine exits at the condenser pressure of 8 kPa. Feedwater leaves the closed heater at 205ºC, 8 MPa, and condensate exiting as saturated liquid at 2 MPa is trapped into the open heater. Saturated liquid at 0.3 MPa leaves the open feedwater heater. The net power output of the cycle is 100 MW. If the turbine stages and pumps are…
Q1) How to steam flow control in thermal power plants?