(c) Figure 1 shows a diode circuit with ac input Vi. Given the values of R1 = 2kN and R2 = 15k2. [Rajah 1 menunjukkan litar diod dengan masukan ac Vi. Diberikan nilai R1 = 2kQ dan R2 = 15k2.] (i) Sketch output Vo and current ir and label its appropriate values. [Lakarkan keluaran Vo dan arus ir dan labelkan nilai-nilai yang berkaitan.] (ii) Determine maximum power at resistor R2. [Tentukan kuasa maksimum pada resistor R2.] İR Vi + + R1 10V Si Vi R2 Vo -10V Figure 1

(c) Figure 1 shows a diode circuit with ac input Vi. Given the values of R1 = 2kN and R2 = 15k2. [Rajah 1 menunjukkan litar diod dengan masukan ac Vi. Diberikan nilai R1 = 2kQ dan R2 = 15k2.] (i) Sketch output Vo and current ir and label its appropriate values. [Lakarkan keluaran Vo dan arus ir dan labelkan nilai-nilai yang berkaitan.] (ii) Determine maximum power at resistor R2. [Tentukan kuasa maksimum pada resistor R2.] İR Vi + + R1 10V Si Vi R2 Vo -10V Figure 1

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
Figure 1 shows a diode circuit with ac input Vi. Given the values of R1 = 2kN and R2 = 15k2. [Rajah 1 menunjukkan litar diod dengan masukan ac Vi. Diberikan nilai R1 = 2k2 dan R2 = 15kQ.] (i) Sketch output Vo and current ig and label its appropriate values. [Lakarkan keluaran Vo dan arus ir dan labelkan nilai-nilai yang berkaitan.] (ii) Determine maximum power at resistor R2.
1- ) Determine the output voltage and diode currents ipi and iD2 for the circuit shown for the two values of input voltage V₁ = OV and V1 = 4 V. Assume that diodes have 0.7V constant voltage drop. 5 V1 le iD1 D1 # R1 10k V2 + --1₁ 5V ..e D2 Vo 5k V3 HOE R2 SV
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=4 V and V2=10 V. R www DZ D1 Vin Vout vi V2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 v and V2=8 V. R DZ D1 Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform Windows hui
In the circuit shown in the figure, draw vx and v0 with a scale according to the input voltages. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, threshold voltages of diodes shall be VE = 0.7V.
5. Assume each diode in the circuit has a cut in voltage of 0.65V. The input voltage is Vi = 5V. Determine the value of R1 required such that ID1 is one half of ID2. What are the values of ID1 and ID2? R1 VD VD1 Vo VD2 V1 5V R2 1kQ ID1 ID2 3. (a die
120 V rms elile a. DI D2 # What is the peak current through each diode? b. What is the P/V for each diode? (Ctrl) - 5ΚΩ
Jump to i) If the input is 10V sine wave, plot the output voltage. The Zener voltage of D1, D2 and D3 are 3.2 V, 3V and 2.8V, respectively. ( R1 ww D1 D2 Vout D3 (ii)Find the output voltage waveform if Vin-150 V and N=3. Assume non ideal diode. D1 D4 D2 RL V out urns Ratio is N:1. lll