c) The rigid beam rests in the horizontal position on two 2014-T6 aluminum cylinders having the unloaded lengths shown. If each cylinder has a diameter of 30 mm, detemine the placement x of the applied 80-kN load so that the beam remains horizontal. What is the new diameter of cylinder A after the load is applied? v, = 0.35. Ans: x = 1.53 m, 30.008 mm. 80 KN 6. B 210 mm 220 mm 3 m

c) The rigid beam rests in the horizontal position on two 2014-T6 aluminum cylinders having the unloaded lengths shown. If each cylinder has a diameter of 30 mm, detemine the placement x of the applied 80-kN load so that the beam remains horizontal. What is the new diameter of cylinder A after the load is applied? v, = 0.35. Ans: x = 1.53 m, 30.008 mm. 80 KN 6. B 210 mm 220 mm 3 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.9.7P: The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting...

See similar textbooks

Similar questions

The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the angle of inclination of the beam after the load is applied. Each support consists of a wooden post with a diameter of 120 mm and an original length (unloaded) of 1.40 m- Consider E = 12 GPa
The wide-flange member is made from an elastic perfectly plastic material. Determine the shape factor for the beam.
For the simply supported beam carrying the concentrated load P = 276 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 2.16 m, E = 12.77 GPa , and I =1681393mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
Question 1) F=11 kN single load, M=22 kN.m moment andA distributed load of w=5 kN/m is effective. The length L is also given as L=5 m.The cross-sectional properties of the beam are; body height Hg=218 mm, body thickness xg=18 mm, flangewidth xf=190 mm, flange height yF13 mm. Point E on the section is flange-It is located just below the body junction. In the section taken from the B line of the beamIt is desired to determine the stress state. According to this;Question 1-A) Find the support response (DY) at point D. (Return your result in kNQuestion 1-B) Find the support response (Ay) at point A. (Return your result in kNwrite.)Question 1-C) Find the shear force (VB) at point B. (KN your resulttype in size.)
The beam is made of southern pine for which Ep = 13 GPa. Determine the displacement at A.
Given the 200mm x 400mm beam with the loading shown, determine: a. the amount of load P applied on the beam if the deflection on the midspan is 5 mm downward. b. by this same load P, what is the deflection and slope on the beam at point D? Set the parameters as a = 3m, L = 9m , E = 200 GPa. EI is constant.
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
Determine the slope at B and maximum displacement of the beam. Use the moment-area theorems. Take E=200GPa and I=550X10^6 mm^4. Draw the shear diagram, moment diagram, and deflection diagram in the process.
The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting between points A and C. Determine the angle of rotation ÔAat the free end A>(Obtain the solution by using the modified form of Castigliano's theorem.)
The load on a cantilever beam AB has a triangulardistribution with maximum intensity q0 (seefigure). Determine the angle of rotation θB and thedeflection δB at the free end.
Question 3The beam AD is made of a solid steel bar. Determine the slope at point B. Use E =200 GPa
Use the Moment-Area theorems and determine the slope at A and displacement at C. EI is constant. Draw the shear diagram, moment diagram, and deflection shape diagram in the process.