Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for staticequilibrium in the position shown? What is the tension Tin cable CD?TA44°D1.8'CB63 lb

Answered: Image /qna-images/answer/ff8c14b3-16a9-4df4-9b58-adf48bb56ade.jpg

Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required fo equilibrium in the position shown? What is the tension T in cable CD? T A 44° D 1.8' C B 63 lb

Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required fo equilibrium in the position shown? What is the tension T in cable CD? T A 44° D 1.8' C B 63 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.59P: How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull...

See similar textbooks

Related questions

Q: Consider the following framework, (NOT drawn to scale): 10 kN 10 kN 60° 30° 30 D 4 m (a) Determine…

Q: Question 7 When there are consistently about 36 defective parts for every 6,000 produced, what is…

A: Solution.jpg

Q: 2 lgium M=1.96 KN-mm Detrmine a bending stresses of beam. 200mm 125 3 50 250 mm. 125mm 25 -1

Q: During a drilling operation, the small robotic device is subjected to an (800 N) force as shown.…

Q: id flows at a speed of 7.5 m/s in a pipe with a diameter of 35 cm. What is the power, in W, of the…

A: Given:v=7.5 m/sd=35 cm =0.35 mpressure drop, ∆P=6300 Pa

Q: Non-destructive testing of large molded pieces may be performed using radiation. Discuss what…

A: Given question: Discuss what constructive elements a non-destructive testing system should contain,…

Q: An object moving with speed of 5 m/s has kinetic energy of 1200 J. Find the mass of object

A: Given data : Kinetic energy (K.E)=1200 J Velocity (V)=5 m/s Required : Mass of object

Q: A fighter aircraft flies at speed of 650 m/s at an altitude of 9.0 km. It is powered by a single…

A: Given Data The fighter aircraft intial speed is:Vi=650 m/s The altitude is:Al=9 km=9000 m The inlet…

Q: (c) Estimate the efficiency of the jack for raising the load. (d) Estimate the power required to…

Q: 9. For the composite areas shown, determine the moment of inertia with respect to the centroidal…

A: Draw the first diagram with centroidal axis.

Q: Q1/ The bar shown in Fig. 1 is subjected to a tensile load of 50 KN. Find the diameter of the middle…

Q: A household freezer opera a rate of 2 kW to maintain power input required to o

A: Calculated the smallest power input(KW) required to operate the freezer.

Q: PESTEL analysis for coffee cultivation in Malaysia.

A: INTRODUCTION: The hot beverage has been consumed by humankind for almost 600 years. This drink is…

Q: 3 E=20000MPa I=1.61x10^6 sqmm Analyze the structure using Consistent Deformation Method. Draw Shear…

Q: Part 2 Discuss the following related to the principles of operation for a gas turbine power plant A.…

A: A. Closed gas turbine cycle 1.Here first the air is compressed in the compressor and then heated in…

Q: The maximum velocity attained by the mass of a simple harmonic oscillator is 10 cm/s, and the period…

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: Correct answer: (d) 3.07 kips

Q: Choose the correct answer for five points only ) The tension Tin the cable AB is maintained at a…

Q: Determine the maximum flow through a 1.2-m diameter concrete culvert which is laid on a slope of…

Q: What would happen if a body (Practical) ?reach resonance case Collapse the mechanism O Vibrate at…

A: To find :- Correct option

Q: The specific volume of a liquid is the :reciprocal of weight density specific volume O specific…

A: To find : reciprocal of specific volume of a liquid

Q: Symmetrical objects can be effectively shown using a Select one: O A. Half O B. Quarter O C. Full…

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

Q: When the minor and major axes of an ellipse are the same, what shape is former Select one: O A.…

A: Consider following equations of given curves: Ellipse: x2a2+y2b2=1 Hyperbola: x2a2-y2b2=1 Circle:…

Q: Hypothetical metal has an FCC crystal structure. If its density is 22.4 g/cm3, and atomic weight is…

Q: In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final)…

Q: * A Carnot heat engine operates between a source at 1000 K and a sink at 300 K. If the heat engine…

Q: A rigid horizontal bar of negligible mass is connected to two rods as shown. If the system is…

Q: Q2: an ammonia vapour compressor refrigerator has a single acting stage, single acting reciprocating…

Q: 3. A horizontal nozzle reduces from 100 mm bore diameter at inlet to 50 mm at exit. It carries…

A: The pressure at the narrow end is 196.036 kPa.

Q: 1-Compare between impulse and reaction turbine with the aid of a neat diagram.

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2- 8 Air flows at a speed of 6.5 m/s through a pipe with a diameter of 25 cm and a length of 30 m.…

A: Answer: The total head loss in this pipe is 1144.755 m.

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

Q: * نقطتان (2 An outside micrometer would be appropriate for measuring which of the :following (two…

Q: Q2 (a) Describe briefly four characteristics of a heat engine. Sketch a simple diagram of a

Q: What is the measure of absolute pressure due to the weight of air molecules above a certain height…

A: Given = multiple choice question is given

Q: how does a pilot check valve differ from a simple check valve

A: The check valves are used for the seal age purpose in the closed position. The valves are used for…

Q: 29.43 +8+20= 32+.5mv2^2 v2 = 2.25 m/s as it passes point B

A: calculated the value of mass (m).

Q: Q3: For the stresses at the point shown, find the followings: 1- The maximum shear stress. 2- The…

Q: 12. A torsional pendulum has a natural frequency of 200 cycles/min when vibrating in a vacuum. The…

Q: An alloy system consists of two metals A&B which are soluble in each other in all proportions in the…

A: The phase diagram and the corresponding point for the given wt% of A and B is shown below.

Q: Four steel bars jointly support a mass of 15 Mg as shown. Each bar has a cross-sectional area of 600…

Q: B- A Refrigerant 134a is contained in a closed, rigid tank of volume 0.2 m³. Initially the…

A: Answer: (a) The mass of refrigerant is 13.2332 kg. (b) The amount of heat is 1854.3157 kJ.

Q: The copper-nickel system is a simple alloy system, as indicated by its phase diagram. Why is it so…

A: In materials with more than one component, a phase diagram depicts the spectrum of possible phases.…

Q: A single stage, double acting air compressor is required to deliver 14 m³ of air per min measured at…

Q: (a) A feedback control system has the following characteristic equation. 5³+(4+ K) s² + 6s+ 8(K + 2)…

Q: (USCS units) A GO/NO-GO plug gage is needed to inspect a 1.000 ± 0.020 in diameter hole. A wear…

Q: re below. If 87% convers tor. te above process. for the overall and sub

A: Given:

Q: -3 ft- -3 ft- 1 ft Locate the centroid (, y) of the composite area. a) = 0.97 fty = 0.45 ft Ob) =…

Q: The shear strength of a metal is commonly determined in which one of the following tests: Group of…

A: The below table describes the determination of corresponding stress for a corresponding test.…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static
equilibrium in the position shown? What is the tension Tin cable CD?
T
A
44°
D
1.8'
C
B
63 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull of a docked ship? The static coefficient of friction between the capstan and the rope is 0.25.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
I need your help expert. The system shown below is in equilibrium. Spring 3 is known to have a change in length of 10 cm. The magnitude of the compressive force in Spring 2 is 15% more than the magnitude of force P, while the magnitude of the compressive force in Bar 1 is 100 N less than that in Spring 2. If the spring constants of Springs 2 and 3 are 625 and 1200 N/m, respectively, determine the following: a. magnitude of forces P (in N) and F (in N) b. tension (in N) in cable ABC c. mass (in kg) of Block A d. compressive force in Bar 1 e. change in length (in cm) of Spring 2 Draw the complete FBD’s of Block A, Hook C and Pulley E. (Note: Below are the final answers, kindly match your answer on this. Thank you) Answer: P = 131.2831 N, F = 87.1569 N, TABC = 110.7024 N, mA = 15.6338 kg, F1 = 50.9756 N, s2 = 24.1561 cm
1. What is a Spatial Force System? 2.Three-dimensional equilibrium problems for a rigid body can be solved using what procedure?
The uniform plate has a weight of W = 450 lb. Suppose that F= 250 lb. The plate is supported by cables A, B, and C as shown below. Determine: A) The tension in the supporting cable A. B) The tension in the supporting cable B. C) The tension in the supporting cable C.
The hanging mobile pictured above consists of two masses, m1 and m2, suspended from a uniform 10 cm long rod, which is in turn suspended from the ceiling at an angle of 70 as pictured above. The mass m1 is 0.02 kg, while the mass of the rod is mr = 0.01 kg. Assuming the mobile is in a state of static equilibrium, find the value of mass m2.
Application of Equilibrium Solve for the value of unknown variables Given P1 = 1.39 KN P2 =6.05KN W1 = 4 KN/m Unknowns a. RAy , RBy , RBx , MB b. value of internal moment 2m to the left of support B
A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
The bar AC is supported by a joint at A and a pin B that is free to slide in the same direction (alpha) of the bar. A bar is connected at C and a force is applied in the theta direction. Consider that L1 = 2.7 m, L2 = 1.7 m, alpha = 13 °, theta = 25 °, and P = 68 kN. Determine the magnitude of the force (kN) on pin B.
A sign of weight 2280 N is supported as shown by a ball and socket support at A and two cables BC and AD 1- Tension in cable BC is (N) : (a. 4560 - b. 6840 - c. 5700 - d. 7980 - e. 9120 ) 2- Tension in cable AD is (N): (a. 10260 - b. 13680 - c. 15960 - d. 18240 - e. 10640 ) 3-Magnitude of x-component of reaction at O is (N): (a. 5700 - b. 6840 - c. 7980 - d. 9120 - e. 10260 ) 4- Find Magnitude of y-component of reaction at O is (N) 5- Find Magnitude of z-component of reaction at O is (N)
A motorized cable car weighs 1 MT, carrying a loadP is traveling along a straight horizontal cable from point A to point B which are 1 Km apart At the instance when the car is 500 meters away from point A, the cable sagged 30 meters. The tension that acts at point A in kN is round off your answer into 2 decimal places). 2.) the minimum tension in kN (round off your answer into 2 decimal places) would be