Cable AD in (Figure 1) is tightened by a turnbuckle and develops a tension of 1500 lb.. Figure 300 108 15 A 12.5 8 FAE 158 1 of 1 Determine the tension developed in cable AB. Express your answer in pounds to three significant figures. 1977 ΑΣΦ. 11 vec FAB Submit Part B Request Answer Determine the tension developed in cable AC. Express your answer in pounds to three significant figures. FAC AE i vec Submit Request Answer Determine the force developed along the z axis of the antenna tower AE. Express your answer in pounds to three significant figures. VE ΑΣΦ It vec BASSO ? ? ? lb lb lb

Cable AD in (Figure 1) is tightened by a turnbuckle and develops a tension of 1500 lb.. Figure 300 108 15 A 12.5 8 FAE 158 1 of 1 Determine the tension developed in cable AB. Express your answer in pounds to three significant figures. 1977 ΑΣΦ. 11 vec FAB Submit Part B Request Answer Determine the tension developed in cable AC. Express your answer in pounds to three significant figures. FAC AE i vec Submit Request Answer Determine the force developed along the z axis of the antenna tower AE. Express your answer in pounds to three significant figures. VE ΑΣΦ It vec BASSO ? ? ? lb lb lb

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.9P: Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For...

See similar textbooks

Similar questions

If the bolt length is 220 mmmm and the sleeve length is 200 mmmm, determine the tension in the bolt when a force of 50 kNkN is applied to the brackets. Express your answer to three significant figures and include appropriate units. Given: The bolt AB in (Figure 1) has a diameter of 21 mmmm and passes through a sleeve that has an inner diameter of 42 mmmm and an outer diameter of 52 mmmm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown.
PROBLEM 1: Determine the tension in each cable and the components offorce reaction at D needed to support the load. Required: 1. Find Dx (Answer: 1039.230 N), Dy (Answer: 0 N) and Dz (Answer: 0 N) 2. Find Tension AB (Answer: 467.667 N) and Tension (Answer: AC 673.808)
9-8kN stress/force on the AB rope holding the base station shown below There are. In order for the net force at point A of this base station to be downward What is the stress/force that should be on the AC rope? A) 5556 N C) 7356 N B) 8200 N D) 3648 N E) 1228 N
load of 12 kN is raised by means of a screw jack. The mean diameter of the square threaded screw is 48 mm and the pitch is 12 mm. A force of 180 N is applied at the end of a lever to raise the load. Determine the length of the lever to be used and the mechanical advantage obtained. the screw self-locking? Take µ = 0.12.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test. A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50 mm and initial diameter of d0=13 mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 506 MPa , e = 689 MPa , g = 585 MPa , and h = 0.146 mm/mm . A) Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 53.0 mm . B) Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 16.0 kN , find the nominal stress experienced by the rod. C)Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the direction of length. Determine the change in volume. Take E = 2x105 N/mm2and μ= 0.25.
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.