2. A cantilever beam of rectangular section is 100mm broad and 150mm deep and carries a concentrated load of 15kN at its free end.Neglecting the weight of the beam find the distance from the free end where the stress at the outer fibres is 75MN/m².

2. A cantilever beam of rectangular section is 100mm broad and 150mm deep and carries a concentrated load of 15kN at its free end.Neglecting the weight of the beam find the distance from the free end where the stress at the outer fibres is 75MN/m².

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.15P: A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A...

See similar textbooks

Related questions

Q: 5. A Vapor Compression Cycle using ammonia has an evaporator pressure of 316.02 kPa and a condenser…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ - 20 kN applied at A. Assume a…

Q: What is the purpose of a flywheel in a machine?

A: Given: What is the purpose of a flywheel in a machine?

Q: A container of a gas is at 25°C and 270kPa. If it can withstand a pressure of 1000 kPa, at what…

A: Given data: Initial temperature of the container, T1=25oC The initial pressure of the container,…

Q: What If? If the incline under m2 is rough, what is the minimum value of the coefficient of static…

A: A block and sphere are connected by a cord that passes over a pulley as shown. Neglect friction and…

Q: The assembly is used to support the 130-kg container having a center of mass at G. The spring has an…

Q: Answer the following, based on the figure below. VF 11 VG = Q= Pc = 1.9 m 0.4 m DN150 Schedule 40…

A: To Find : The velocity and flow rate and pressure vf,vG,Q, Pc and PG Given : The diameter at point G…

Q: Question 4- On the diagram 1. Draw velocity vector of B 2. Find magnitude of linear velocity of B 3.…

A: To Draw : 1) The velocity vector of B 2) The magnitude of linear velocity of B Given : The diagram…

Q: Ice cube is cooled using heat engine. The T-initial of cube is 373 K and lowered to a T-final of 273…

Q: If, at the instant shown, bar AB has an angular velocity @AB = 5 rad/s CW: a) Using a diagram,…

Q: A load of P = 91 kN is supported by a structure consisting of rigid bar ABC, two identical solid…

A: The given information in the problem is shown in the following attached image:

Q: Engine oil at 100°C flows on the top surface of a 1-m-long flat plate maintained at 20°C. The oil’s…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the…

Q: 4. In an oil refinery, certain oil with sp.gr 0.91 flows with a velocity of 0.5 m/s in a pipe of…

A: The given data for the above problem are: Specific gravity = 0.91 Density of oil = 0.91×1000 = 910…

Q: Abar having a length of 5 in and cross-sectional area of 0 7 in² is subjected to an axial force of…

A: Given data:- Length of the Bar =5 in cross-sectional area =0 7 in2 axial force= 8000 lb Deformation…

Q: The cylindrical tank has an inner diameter of 450 mm, the wall thickness is 6 mm, and point a is the…

A: (a) Write the given data. di=0.450 mt=0.006 mP=1.5 MPa

Q: How many and what kinds of materials are needed to start a thread?

A: To start a thread, you typically need the following materials: Thread material: This can be made…

Q: A 800N package is supported by two cables and a rod as shown. 1600mm 600mm. 600mm B 1800mm 1200mm…

A: According to the given data Coordinates of the point A=(0, 1.8, 0.8)m B=(-0.6 , 0 1.2)m C=(0.6 , 0…

Q: wo aluminum ingots, one weighing 1.5 kg at 450 degrees celsius while the other is 1.1 kg at 250…

Q: Problem 6.2 The gap between a moving plate of height H and a stationary wall is filled with an…

A: The plate is pushed to the right with constant speed Vplate. The density of the liquid is ρliq. The…

Q: Note: m = 5 kg Solve the transfer function T(s) = x2/F(s) if b1 = 2, b2 = 4, K1= 5 and k2 = 7 k₁ ww…

A: The values are m=5 kg, b1=2, b2=4, k1=5, k2=7

Q: A fireworks shell P is launched determine the values of r and upward from point A and explodes at…

Q: Water at 40 °C (density = 992.3 kg/m3 v = 0.664 × 10−6 m2/s) flows at a velocity of 2 m/s through a…

A: First, we need to calculate the Reynolds number to identify the type of flow inside the pipe. Given…

Q: Calculate the size of a cylindrical riser (Height and diameter equal ) necessary to feed slab…

Q: F7-15. Use the moment-area theorems and determine the slope at A and displacement at C. El is…

A: For solution refer below images.

Q: Determine the deformation of the beam at point H due to the load P. Assume that El is constant…

A: The given information in the problem is shown in the following attached image:

Q: A 5 ft DU B 5 ft -3 ft-

Q: 3. If FAB cannot exceed 500 pounds, determine the maximum angle 0 permitted in this system. Hint:…

Q: he condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: Question #5 In figure below, determine the reactions at the supports. 900 N/m -3 m- 600 N/m -3 m

Q: The shaft, lever, and handle are welded together and constitute a single rigid body. Their combined…

A: Given m=21kgthe coordinates of point C is: 0, 535, -280the coordinates of point D is: 355, 0, -280

Q: An elbow for the duct of a ventilation system is made of sheet metal of uniform thickness. Locate…

A: Given- An elbow for the duct of a ventilation system is given. To locate the centre of gravity of…

Q: 1.C3 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Each of the three pins…

A: Given: To find: Program to find normal, shear, bearing stresses Permissible diameter

Q: 60 mm F 10000 N.mm 80 mm A y 600 N D C 45 mm E 90 mm 120 mm 300 N A: a collar that can slide along…

A: Force along negative Y-axis F1 = 600 N Force along positive x-axis F2 = 300 N A coller rotate about…

Q: Saturated liquid refrigerant 134a at 900 kPa is throttled to a pressure of 200 kPa. What is the…

Q: Given the following system setup, determine the value of h. Q-0.1 m^3/s 0.15 diameter 1m O Air 0.3m…

Q: A cantilever beam has the cross section and loading shown below. Determine its factor of safety with…

Q: The frame of a greenhouse is constructed from uniform aluminum channels. Locate the center of…

Q: If both carriages have a total mass of 200 g and the sliding carriage is at a radius of 20 cm, what…

A: The following apparatus is normally used for the given problem. On a horizontal beam, two carriages…

Q: 1. A 5,000 kg/min of water at 35°C enters a cooling tower where it is to be cooled to 20 °C. The…

A: “Since you have posted multiple questions, we will provide the solutiononly to the first question as…

Q: For the solid shaft shown in the figure, determine the maximum shearing stress. And the twisting…

Q: Train A travels with a constant speed VA = 95 km/h along the straight and level track. The driver of…

Q: An electronics device generates 37.5 W of heat energy during normal operation. The heat is…

A: heat transfer by convection is given by newton law of cooling ... Q=hA(deltaT)

Q: The principal stresses at a material point in the state of plane stress are 8 MPa and -2 MPa. a)…

Q: 2. As shown in the picture, all the rods in the isosceles triangle truss structure are made by…

Q: A statically determinate three-hinged arch is shown below, L = 1.5 m and P = 3 kN. Compute the…

A: (a) Draw the free-body diagram of the beam.

Q: 1. A beam of regular cross section -rectangular- is 64mm broad,100mm deep and 1.6m long. It is…

A: Given that: Length of beam, L=1.6 m,Breadth of beam, b=64 mm,Depth of beam, d=100 mm,Load at the mid…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: The given information in the problem is shown in the following attached image:

Q: In a standard Rankine cycle steam enters the turbine at pressure p3=10mpa and temperature T3=350c…

A: Given data: The inlet pressure at the turbine is, p3=10 MPa. The inlet temperature at the turbine…

Q: Hello, sorry for not clarifying which parts to solve, could you please do part D?

A: Given data:- The speed of the impact is doubled To find:-the maximum compression of the spring

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

2. A cantilever beam of rectangular section is 100mm broad and 150mm deep and carries
a concentrated load of 15kN at its free end.Neglecting the weight of the beam find the
distance from the free end where the stress at the outer fibres is 75MN/m².

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported wooden I-beam with a 12-ft span supports a distributed load of intensity q = 90 lb/ft over its length (see figure part a). The beam is constructed with a web of Douglas-fir plywood and flanges of pine glued to the web, as shown in the figure part b. The plywood is 3/8 in. thick: the flanges are 2 in, × 2 in, (actual size). The modulus of elasticity for the plywood is 1,600,000 psi and for the pine is 1,200,000 psL Calculate the maximum bending stresses in the pine flanges and in the plywood web. What is q, if allowable stresses are 1600 psi in the flanges and 1200 psi in the web?
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
-14 A simply supported composite beam with a 3.6 m span supports a triangularly distributed load of peak intensity q0at mid-span (see figure part a). The beam is constructed of two wood joists, each 50 mm x 280 mm, fastened to two steel plates, one of dimensions 6 mm × 80 mm and the lower plate of dimensions 6 mm x 120mm (see figure part b). The modulus of elasticity for the wood is 11 GPa and for the steel is 210 GPa. If the allowable stresses are 7 MPa for the wood and 120 MPa for the steel, find the allowable peak load intensity q0maxwhen the beam is bent about the z axis. Neglect the weight of the beam.
A r o lukI f/frm f «m t ub e of ou t sid e d ia met er ^ and a copper core of diameter dxare bonded to form a composite beam, as shown in the figure, (a) Derive formulas for the allowable bending moment M that can be carried by the beam based upon an allowable stress <7Ti in the titanium and an allowable stress (u in the copper (Assume that the moduli of elasticity for the titanium and copper are Er- and £Cu, respectively.) (b) If d1= 40 mm, d{= 36 mm, ETl= 120 GPa, ECu= 110 GPa, o-Ti = 840 MPa, and ctqj = 700 MPa, what is the maximum bending moment Ml (c) What new value of copper diameter dtwill result in a balanced design? (i.e., a balanced design is that in which titanium and copper reach allow- able stress values at the same time).
A reinforced concrete T-beam (see figure) is acted on by a positive bending moment of M = 175 kip-ft. Steel reinforcement consists of four bars of 1.41-inch diameter. The modulus of elasticity for the concrete is Ec= 3000 ksi while that of the steel is £s = 29,000 ksi. Let b = 48 im, rf = 4 in., bw=15 in,, and d = 24 in, Find the maximum stresses in steel and concrete, If allowable stresses for concrete and steel are o"ac = 1400 psi and tr^ =18 ksi, respectively, what is the maximum permissible positive bending moment?
A wood beam with cross-sectional dimensions 200 mm x 300 mm is reinforced on its sides by steel plates 12 mm thick (see figure). The moduli of elasticity for the steel and wood are E±= 190 GPa and Ew= 11 GPa, respectively. Also, the corresponding allowable stresses are eS= 110 MPa and ew = 7.5 MPa, (a) Calculate the maximum permissible bending moment Mmaxwhen the beam is bent about the- axis. Repeat part (a) if the beam is now bent about its y axis. Find the required thickness of the steel plates on the beam bent about the y axis so that Mmaxis the same for both beam orientations.
A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section (b = 75 mm, h = 150 mm). Calculate the reactions of the beam and the displacement at point C. Assume that E = 190 GPa.
A rectangular bar having width twice the depth is used as a beam. The beam is made of mild steel material having elastic modulus of 2.1 x 105 N/mm? and it undergoes bending by external load which makes radius of curvature of 150 m. If the allowable bending stress in the beam is to be limited to 100 MN/m. find the cross section of the beam.
Uniformly distributed load on a simple support beam with a length of 6 metersMaximum that occurs on the cross section when q is appliedIf bending stress is 337.5MPa,How many kN/m is the equal distribution load q?(However, the cross section of the beam is wide x height = 40mm x)100 mm.)
A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed3.25 N/mm2 find the load w.
A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10 N/mm^2, determine maximum udl it can carry.