Cables AB and AC are connected at point A at a height of 10 m from ground. The magnitude of the force Falong AC is 850 kN. (a) Determine the magnitude of the components of the force F acting along and perpendicular to the cable AB. (b) Determine the angle made between the force F and cable AB.

Cables AB and AC are connected at point A at a height of 10 m from ground. The magnitude of the force Falong AC is 850 kN. (a) Determine the magnitude of the components of the force F acting along and perpendicular to the cable AB. (b) Determine the angle made between the force F and cable AB.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Draw a Free Body Diagram of Point B and; 2. Solve for the Forces in cable-T1, and cable-T2

Q: 0.35 m B. 0.4 m 20° -y 15 kg 0.7 m 0.45 m А W

A: Construction methods that involve tensioning are used to reduce the amount of traction load applied…

Q: for the cable shown. determine the following. a. reactions of the cable b. the sag y at the 45…

A: To find reaction at cable end,sag,and cable length

Q: The cable is subjected to a 150-N horizontal force at B, and an 80-N vertical force at C. Determine…

Q: Determine the maximum tension developed in the cable if it is subjected to the triangular…

A: The equation for cable is given by, Substitute the value in the above expression and integrate.…

Q: Refer to Fig. 2.4. The tension in the cable BD is 1 kN. As a result, cable BD exerts a 1-kN force…

A: The given figure is shown below:

Q: The cable stretches between two points A and B which are L = 60 m apart and at the same elevation.…

A: A cable is shown in the question which has been stretch between between two points which are 60…

Q: . The cable supports the loading shown. Detemine the magnitude of the vertical force P so that yc =…

Q: 2. A cable supports two concentrated loads at B and C, as shown. Determine the sag at B, the tension…

Q: 4. A cable 800 m long weighing 1.5 kN/m has tension of 750 kN at each end. Note: Treat this as…

Q: The left support of the cable shown is located 10 m below the right support. The lowest point on the…

A: Solution Given Data L=100 m w=300 kN

Q: Compute the maximum loading (kN) in the cable. E 1.5 m C 1 m 4 kN -5 m -4 m -4 m

A: To find maximum loading in cable

Q: The cable supports a girder which weighs 850 lb/ft.Determine the tension in the cable at points A,…

Q: 3. A parabolic cable supports a girder having a weight of 12 kN/m. a) Determine the tension of the…

A: a) Determine the tension of the cable at C. b) Find the maximum tensile force of the cable.…

Q: a)Determine the magnitude of the projected component of the force F = [ 60 i + 12 j - 35 k ] N along…

A: Given :

Q: The cable AB carries a tension of 470 N. Determine the moment about O (positive if counterclockwise,…

Q: Calculate the tension in the cable, and the reactions at A and C 100 mm 100 mm 300 mm 400 N C 400 N…

Q: The cable stretches between two points A and B which are L = 60 m apart and at the same elevation.…

Q: Given the Cable as shown below that weighs 15 N/m with the tensile force at Point B that is found to…

Q: The cable shown cames a total vertical load of 190kips, uniformly distributed with respedt to the…

Q: The cable AB supports a uniformly distributed load of 12lb/ft. Determine the maximum force in the…

A: The slope of the cable is higher at point B. Therefore, the maximum tension in the cable occurs at…

Q: THE CABLE ABCD IS HELD IN THE POSITION SHOWN BY THE HORIZONTAL FORCE P. DETERMINE P AND THE FORCE IN…

Q: 1. The cable is subjected to a uniform loading of w = minimum tension in the cable. 250 lb/ft.…

A: As per our guidelines we are supposed to answer only first question. Kindly repost other questions…

Q: The left support of the cable shown is located 10 m below the right support. The lowest point on the…

A: Consider the free body diagram;

Q: The 6m boom has a fixed end A. A steel cable is stretched from the free end B of the boom to a point…

A: Given: The length of the boom is 6 m. The tension in the cable is 5 kN. Consider the figure,

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 880…

Q: Problem 2: _If the tension in the cable is F = 1400 N, determine the magnitude of the moment…

Q: The cable is subjected to a 150-N horizontal force at B, and an 80-N vertical force at C. Determine…

Q: Determine the resultant force, together with its angle, of the system shown. -note:The tension…

Q: The cable shown carries a total vertical load of 100kips, uniformly distributed with respect to the…

Q: The cable is subjected to a uniform loading of w = 250 lb/ft. Determine the maximum and minimum…

A: The tension in cable develop due to the load carried by them, cable structures are generally used in…

Q: A 50 kg load is lifted by the pulley system shown. Determine the tension in the cable ABC and the…

A: As all cables which are connected by the centre of pully at B and cable ABC are one and connected by…

Q: The left support of the cable shown is located 10 m below the right support. The lowest point on the…

Q: The cable is subjected to a uniform loading of w = 250 lb/ft. Determine the maximum and minimum…

A: The given figure is shown below:

Q: Situation 7. Determine the magnitude of force F in cable AB in order to produce a moment of 500…

A: find the position vectors: rCA=6-0i+0-0j+0-0k=6i ftrCB=0-0i+4-0j+12-0k=4j+12k ft find the unit…

Q: Problem III. A cable was used to dry the clothes from wet laundry by hanging as shown below. The…

Q: The cable AB is subjected to a uniform loading of 160 N/m. If the weight of the cable is neglected…

A: To find Maximum tension developed in the cable

Q: 7 ft 4 ft B 150 lb -5 ft 4 ft -3 ft 100 lb ...

A: DETERMINE THE TENSION IN SEGMENT AB, CD AND BC OF THE GIVEN CABLE

Q: The cable AB carries a tension of 280 N. Determine the moment about O (positive if counterclockwise,…

A: Determine the moment about O ,M=?

Q: 34 35

Q: Q3): For the cable subjected to a uniform load of (last two digits of your student Number in KN/m)…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: The cable of length ℒ = 20 m is suspended between two points A and B a distance of 6 m apart. If…

Q: THE CABLE CARRYING 40-lb LOADS AT B AND C IS HELD IN THE POSITION SHOWN BY THE HORIZONTAL FORCE P =…

A: The given figure is shown below:

Q: *Given the Cable as shown below that weighs 4.0 N/m with 30 N horizontal load applied at the roller…

Q: If the weight of the boom is negligible compared with the applied 29-kN load, determine the cable…

A: B→ = 9k^C→ = -3i ^+2j^BC→ =-3i ^+2j^-9k^cosα =-3(-3)2 +(2)2+(-9)2cosα = -0.309cosβ = 2(-3)2…

Q: *5-28. The cable of length L= 20 m is suspended between two points A and B a distance of 6 m apart.…

Q: A uniform pipe cover of radius r = 240 mm and mass 30 kg is held in a hor- izontal position by the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 (a) Magnitude of components

VIEW

Step 3 (b) Angle between force F and cable AB

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that approximately loads the cable by a uniform q(x) = q0. If l (small letter L) = 10 m, hA = 5 m, and hB = 4 m. Compute the maximum force in the cable for its minimum distance to the group by 3 m. q0 (kN/m) 12.213
The top end of vertical boot is connected by two cables having tension T1=500N and T2=1500N as shown in the figure. The third cable AB is used as a guy wire. Determine the tension in cable AB if resultant of three concurrent forces acting at A is vertical?
Determine the resultant force, together with its angle, of the system shown. -note:The tension exerted by the cable tied to point B is 60N and the one that reaches point C is 40N.
q0 (kN/m) = 20.627 A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that it approximately loads the cable by a uniform q(x) = q0. If l = 10 m, hA = 5 m, and hB = 4 m, compute the maximum force in the cable for its minimum distance to the ground by 3 m.
Determine the Velocity of Cable at Point C and block W. And the relative Velocity point C and block W with respect to Block E. Note: Block E is moving downward with a velocity of 4m/s.
13. A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE and BF as shown in Figure 2. Knowing that the tension in cable CD is 14 KN and assuming that CD is parallel to the x-axis (0), determine the horizontal component of the reaction at A. A. 7.00 kN B. 17.50 kN C. 22.4 kN D. 2.50 kN
Determine the magnitude of the projection of the force F1 along cable AC.
Determine the tension in cable BD if P = 51 N.
Determine the total length of cable, If y=20m. a.) 177.809 KN b.) 176.089 KN c.) 175.980 KN d.) None of the above e.) 178.908 KN
The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 620 N, determine the n- and t-components of this force acting on point A of the bar.
In Prob. 3.59, determine the perpendicular distance between cable AE and the line joining points D and B.(Reference to Problem 3.59):The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF . If the force exerted by cable AE at A is 55 N, determine the moment of that force about the line joining points D and B.
The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 7.7 kN. Determine the required tension T in cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force.Assume a = 41 m, b = 48 m, c = 29 m, and d = 35 m.