Cagayan port (where the water is observed to have a sp.gr. of 1.03 )the barge has a draft of 3.8 m and the portion of the barge at the water line measures 300 m by 60 m. Loaded with the reinforcing bars in Cebu City bay (where the sea water is observed to have a sp.gr. of 1.05, the vessel chief mate recorded a draft of 7.2 m. If it costs P5 to transfer a bar of a given dimension, determine how much would it costs Engr. Robredo for the transfer in thousands of pesos. Use unit weight of steel to be 7.85

Cagayan port (where the water is observed to have a sp.gr. of 1.03 )the barge has a draft of 3.8 m and the portion of the barge at the water line measures 300 m by 60 m. Loaded with the reinforcing bars in Cebu City bay (where the sea water is observed to have a sp.gr. of 1.05, the vessel chief mate recorded a draft of 7.2 m. If it costs P5 to transfer a bar of a given dimension, determine how much would it costs Engr. Robredo for the transfer in thousands of pesos. Use unit weight of steel to be 7.85

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bucket: 8.5 lbBucket + concrete: 58.7 lbVolume: 0.265 ft3Density of Concrete: _____________lb/ ft3ASTM DESIGNATION: _____________
The loading on the bookshelf is distributed as shown. Determine the magnitude of the equivalent resultant location, measured from point O.
Hey hows it going, this is a problem from my Structural Analysis course. I am havinig trouble understadning dead loads on girders. The solution is posted on Bartleby. For the dead loading acting on the girder AG, the solution only accounted for the weight of the girder itself. This does not make sense to me because doesnt the girder also support a portion of the concrete slab? Thanks!
a) A solid wood cylinder of specific gravity 0.6 is 300mm in radius and 1.2 meters high. If vertically placed in oilwith specific gravity 0.85, would it be safe?b) A barge floating in fresh water has the form of a parallelepiped having dimensions 10m x 30m x 3m. It weighs4500kN when loaded with center of gravity along its vertical axis 4m from the bottom. Find the metacentricheight about its longest and shortest centerline, and determine whether or not the barge is stable.
Tarentum Sdn. Bhd. is a consultant specialized in structural failure investigation in KualaLumpur. This company has been assigned to investigate the collapsed corridor structure in oneof the local government facilities in Kuan tan, Pahang. Figure 1 shows the structural drawing of thecantilever I-Beam which was used to support the corridor slab. The total length of the I-Beamis 2.4 m from A to B. The I-Beam was subjected to a uniform distributed load of 111 kN/rnalong with A to Band a concentrated load of30 kN with a distance of0.8 m from B. a) Draw complete free body diagram and elastic curve for the I-Beam.
Urgent please solve quickly. a = 10 , b = 7 solve this question about this information. Extra information: Take both loads 35 kN
A unit load As/Rs for work-in-process storage in a factory must be designed to store 2000 pallet loads with an allowance of no less than 20% additional storage compartments for peak periods and flexibility The unit load pallet dimensions are: depth(x) = 914mm and width(y) = 1219 mm. Maximum height of unit load is =1067 mm. It has been determined that the AS/RS will consist of four aisles with one S/R machine per aisle. The maximum ceiling height(interior) of the building permitted by local ordinance is 18 m, so the AS/RS must fit within this height limitation. The rack structure will be built 610mm above floor level, and the clearance Between the rack structure and the ceiling of the building must be at least 457 mm. Determine the dimensions(height,length,and width) of the rack structure.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f’c = 28 MPa fy = 276 MPa Aps = 800 mm2 Ds = 10 mm Dm = 18 mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250 kN
Determine the ultimate load distribution acting on all beams and girders in the given floor framing below. Assume that the supports are simply supported. Compute for the reactions and loads in each beam. Assume unit weight of concrete to be 23.6 kN/m3. Always simplify your load distributions (distributed loads acting on the same points/locations should be added up). Monolithic FloorAll concrete slabs, t = 100 mmAll concrete beams, b = 250 mm ; h = 500 mmAll concrete columns, 300 mm x 300mm Superimposed LoadsFloor Finish:Ceramic tile ½ inch mortar Ceiling:Wood furringGypsum board ¼ inch thickMechanical Duct Allowance (MDA) Frame Partition:Wood, studs with gypsum board h=2.8m Utilities: twice the weight of MDA Exterior WallsNormal Unit Weight Concrete Masonry/ Concrete Hollow Blocks, CHB4 inch thick with plastering on both faces, full groutheight=3m (no interior walls) Live LoadResidential
Load Balancing Method
A beam of rectangular section must be cut from a circular trunk of diameter D. What is the ratio between the height h and the width b of the beam so that it has the maximum resistance to pure bending? Express your answer as a ratio h/b.
A short column is subjected to a factored load of Pu = 3790 kN. f'c = 27.6 MPa, fy = 414.6 MPa. a. What is the minimum gross cross-sectional area required if it is a tied column? b. How many 22mm diameter longitudinal bars are needed? c. What spacing of 10mm diameter ties should be used?