calculate a) the current in each line b) the current in the Neutral conductor. c) the main neutral conductor supplying these loads was accidentally broken when the 17kW load was being disconnected from the supply. When the supply was switched on again to supply the 25kW and 10kW loads, the main neutral conductor was missing(broken) calculate the voltage across the 25kW and the load 10kW load

calculate a) the current in each line b) the current in the Neutral conductor. c) the main neutral conductor supplying these loads was accidentally broken when the 17kW load was being disconnected from the supply. When the supply was switched on again to supply the 25kW and 10kW loads, the main neutral conductor was missing(broken) calculate the voltage across the 25kW and the load 10kW load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.12P: A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical...

See similar textbooks

Similar questions

A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
In a 3-phase, 4-wire system, the currents in R, Y and B lines under abnormal conditions of loading are as under : IR = 100 ∠30º A ; IY = 50 ∠300º A ; IB = 30 ∠180º A. Calculate the positive, negative and zero sequence currents in the R-line and current in the neutral wire.
A three-phase, 50Hz transmission line with a length of "240" is given. It has values of “27” MVA, 0.8 reverse power coefficient and phase voltage “134” kV (phase-phase) for the end of line. Transmission line conductors are placed “3.2” meters apart. The conductors are known to have a resistance of 0.11ohm/km and a diameter of 1.6cm. Neglecting the leaks and using the π equivalent circuit; ( ε0=8.854*10^(-12) F/m, μ0=4*π*10^(-7) H/m) Find the Inductance and Capacitance of the line for 1 km length? , Find the total ohmic resistance of the line, the total inductive reactance of the line.
Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB and IY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage.
A three-phase transposed line is composed of one ACSR 1,431,000 cmil, 47/7 Bobolink conductor per phase with flat horizontal spacing of 11 meters as shown in Figure (a). The conductors have a diameter of 3.625 cm and a GMR of 1.439 cm. The line is to be replaced by a three-conductor bundle of ACSR 477,000 cmil, 26/7 Hawk conductors having the same cross-sectional area of aluminum as the single-conductor line (Figure (b)). The conductors have a diameter of 2.1793 cm and a GMR of 0.8839 cm. The new line will also have a flat horizontal configuration, but it is to be operated at a higher voltage and therefore the phase spacing is increased to 14 m as measured from the center of the bundles as shown in Figure (b). The spacing between the conductors in the bundle is 45 cm. Determine the inductance and capacitance for both lines. Calculate the percentage change in the capacitance and inductance for both lines. Interpret these changes.
Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB andIY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage. Find the active power (in kW) in the main network and in. each branch and the apparent power (in kV A) using the given information below. Two branches connected in parallel had a p.d. of 200∠30° V applied to them. The currents in the respective branches are 20∠60° A and 40∠30° A. Thanks
In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across the top unit (i.e. near the tower) and middle unit are 10 kV and 11 kV respectively. Calculate (i) the ratio of shunt capacitance to self capacitance of each insulator, (ii) the string efficiency and (iii) line voltage
An 11 KV, 3-phase transmission line has a resistance of 1.5 Ω and reactance of 4 Ω per phase.Calculate the percentage regulation and efficiency of the line when a total load of 5000 KVA at 0.8 lagging power factor is applied at 11KV at the distant end.
Calculate the per phase inductance and reactance of a balanced 3, 60 Hz, line with horizontal phase spacing of 10 m using three conductor bundling with a spacing between conductors in the bundle of 0.3 m. Assume the line is uniformly transposed and the conductors have a 1cm radius.
Suppose a completely transposed 60-Hz three-phase line has flat horizontal phase spacing with 10 m between adjacent conductors. The conductors are 1,590,000 cmil ACSR with 54/3 stranding. Line length is 200 km. Assume the line voltage is 345 kV, at 60 Hz. i) Calculate the inductance in H/m. ii) The inductive reactance in ohm/m.
In a three phase overhead system, each line is suspended by a string of three insulator. The voltage across top unit and the middle unit are 7 kV and 10 kV respectively. Calculate, a) Line voltage. b) String efficiency