Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB andIY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage.

Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB andIY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.
A 50ohm transmission line powered by a 3GHz source and terminated with a load impedance ZL=25-j60 ohms will be matched with the shorted parallel side. What should be the length, in m, of the parallel lateral line calculated using the Smith diagram ?
(Note: Write all the formulas related to problem step by step and neatly) What will be the power loss of a distribution line if the power at the sending and receiving end is 550kVA and 537kVA respectively? What will be its transmission efficiency?
In three-phase short transmission line with end-of-line interphase voltage UR = 31,5kV , from the end of the line active power absorbed PR = 9000 kW, end of line power factor is cosφ = 0,70 (end) and the length of the line is l = 20km, The resistance of the line per km is R'= 0,125 Ohm/km, the reactance per km is X'= 0,375 Ohm/km.With the help of given information; a) Calculate the current drawn from the line (IR) as a phasor. b) Calculate the line-to-line-neutral voltage (VS) as a phasor, determine the effective line-to-line voltage (US) Calculate its value. c) Calculate the line head power factor, active and reactive power drawn from the line head, d) Draw the phasor diagram of the system. ..
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration,conductor resistance and inductance, and conductor radius values to achieve the efficiencyand voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment.b) Find the location and value of the largest voltage drop.
Solve this math : A three-phase 60-hz transmission line has its conductors arranged in a triangular formation so that two of the distances between conductors are 20ft and the third is 40 ft. The conductors are ACSR Rook. Determine the capacitance to neutral in microfarads per mile and the capacitive reactance to neutral in ohm-miles. If the line is 115 mi long, find the capacitance to neutral and capacitive reactance of the line. Note: In the below i have added similer type of math and its ans.In the above math, there is just changes of values and Main Change is ACSR ROOK which is given to then question and in the below question which is solved it was ask ACSR Parakeet. So notice that. Follow This Book for help"POWER SYSTEM ANALYSISAND DESIGN;FIFTH EDITION, SI;J. DUNCAN GLOVER" Now solve the math according to the given way solve the math. "A three-phase 60-hz transmission line has its conductors arranged in a triangular formation so that two of the distances between conductors are 25…
A 300 km long 3-phase transmission line of 154 kV is operated at 60 Hz. The line is on average 1200 m above sea level and instead At 120m, an air outlet decreases by 10 mmHg. Sea free air the dose is 760 mmHg and the puncture strength of the air is 30 kV / cm As it is known, the roughness of the line is 0.89 for the average outdoor temperature of 34 oC, The distance between the conductors is 550 cm and the conductor cross section is 40mm. along the line by calculating the corona voltage and corona discharge voltage calculate the total corona loss that occurred.
In the power system whose single line diagram is shown below, the line cross-section is 95 mm2, the intrinsic conductivity coefficient is 34 m/ohm.mm2 and the inductive reactance of the line is 0.4 ohm/km. According to these values; Calculate the active, reactive and visible components of the currents passing through each line segment.