Calculate F₁ for the beam shown in figure below. Assume it is uniform and has a mass of 250 kg. For the distances assume that D₁ = 1.84 m, D₂ = 4.08 m, D3 = 2.80 m and D4 = 1.06 m. For the forces assume that f3 = 3920 N, f4 = 3090 N and f5 = 1920 N. F₁ F₂ D₂ D₂ ++ D₂ D₁ Submit Answer Tries 0/40 Calculate F₂. Submit Answer Tries 0/40

Calculate F₁ for the beam shown in figure below. Assume it is uniform and has a mass of 250 kg. For the distances assume that D₁ = 1.84 m, D₂ = 4.08 m, D3 = 2.80 m and D4 = 1.06 m. For the forces assume that f3 = 3920 N, f4 = 3090 N and f5 = 1920 N. F₁ F₂ D₂ D₂ ++ D₂ D₁ Submit Answer Tries 0/40 Calculate F₂. Submit Answer Tries 0/40

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.9 × 104 kN·m2 is constant for the beam; w = 6.4 kN/m, LHA = 3.0 m, LAB = 6.0 m.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1. Determine the moment of inertia of the cross section .2. Determine the slope at point B
Calculate the vertical support reaction in support B. Enter your answer in kN to two decimal places.
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.4 × 104 kN·m2 is constant for the beam; w = 3.6 kN/m, LAB = 3.7 m, LBC = 7.4 m, LCH = 3.7 m.
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as shown in figure below. At the vertical wall, f = 0.268 while under the block f = 0.20. Determine the force P needed to start the motion to the right.
As shown in the figure, aluminum rod AB and steel rod BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 6000 lb. If aluminum rod has a cross-sectional area of 0.60 in.² and E = 10 × 103and steel rod has 0.50 in.² and E = 29 × 106 each rod and the horizontal and vertical displacements of point B. Assume α = 60° and θ = 30°. ksi, psi, compute the elongation of
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
A block with weight W (W=75 lbs) can move vertically between two smooth walls. It is held by a rope which passes around three fixed rough pegs (coefficient of static friction u=0.25) as shown in the figure. Calculate the force F which will ensure that the block remains suspended.