Calculate for the axial force in kN at member DC of the frame shown in figure 2 using Cantilever Method. Enter absolute value and use 2 decimal places in your solution. a = 49.5 kN, b = 32.8 kN, c = 4.2 m "a" kN www "b" kN "b" kN D C B 4 m A 40 x 106 mm² H G E 5 m A = 60 x 106 mm² K J A 40 x 106 mm² "C" m "c" m "c" m

Calculate for the axial force in kN at member DC of the frame shown in figure 2 using Cantilever Method. Enter absolute value and use 2 decimal places in your solution. a = 49.5 kN, b = 32.8 kN, c = 4.2 m "a" kN www "b" kN "b" kN D C B 4 m A 40 x 106 mm² H G E 5 m A = 60 x 106 mm² K J A 40 x 106 mm² "C" m "c" m "c" m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate for the axial force in kN at member HG of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
Determine the axial force in member DE in kN. Use F1 = 77 kN, F2 = 60 kN, x = 3.65 meters, y = 3.24 meters. Round off to two decimal places. Input the numerical value only.
An Analyze the frame shown in the figure. Use Cantilever Method. 68. Compute the centroid of columns from the rightmost. a. 7.33 m b. 6.33 m c. 8.33 m d. 5.33 m 2. Compute the axial force on column CF. a. 2.687 kN b. 2.786 kN c. 6.287 kN d. 7.268 kN 3. Compute the moment in column A.D a. 7.605 kN.m b. 5.706 kN.m c. 6.705 kN.m d. 6.507 kN.m
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
Q9c. For the beam below, the point loads and distances are as follows: F1 = 11. 25 kN, F2 = 11.25 kN and F3 = 4.50 kN L1 = 2.25 m, L2 = 4.50 m, L3 = 4.50 m and L4 = 2.25 m Determine the bending moment at D. Give your answer in kilonewton metres (kNm) to two decimal places.
For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 89kips and 31kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
For the fixed ended steel beam shown below (E = 200 GPa),Determine the following:a) Determine the moment at point A in kN-m.b) Determine the moment at point B in kN-m.c) Determine the moment at point C in kN-m.d) Determine the deflection at midspan in mm.
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN