Situation 4. Please answer no. 4. Situation 4: A tension force F of magnitude 5.3 kN is appliedto the cable attached to the top of the rigid mast and securedto the ground.A12.30m0F=5.3 kN9.6 mB7.2 mX1.Compute the component of F along the x-y plane.2. Compute the component of F along the x-axis.3.Compute the moment Mz of F about the z-axis thru thebase of the mast.4. Determine the moment of the force about the origin.

1. Compute the component of F along the x-y plane. 2. Compute the component of F along the x-axis.…

sion force F of magnitude 5.3 kN is applied to the cable attached to the top of the rigid mast and secured to the ground. 12.30m F=5.3 kN 9.6 m B 7.2 m 2. 1. Compute the component of F along the x-y plane. Compute the component of F along the x-axis. Compute the moment Mz of F about the z-axis thru the base of the mast. 3. 4. Determine the moment of the force about the origin.

sion force F of magnitude 5.3 kN is applied to the cable attached to the top of the rigid mast and secured to the ground. 12.30m F=5.3 kN 9.6 m B 7.2 m 2. 1. Compute the component of F along the x-y plane. Compute the component of F along the x-axis. Compute the moment Mz of F about the z-axis thru the base of the mast. 3. 4. Determine the moment of the force about the origin.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniformly distributed load on beam ABC in Figure P6.9 causes it to sag. To counteract this sag, a cable and post are added beneath the beam. The cable is ten- sioned until the force in the post causes a moment equal in magnitude, but opposite in direction, to the moment in the beam. Determine the forces in the cable and the post, and determine the reactions at A and C.
Determine the horizontal and vertical deflection of the hinge at point C of the arch in Figure P8.16 for a single concentrated load of 60 kips applied at joint B in the vertical direction.
If P = 20.3 and M = 6.83, Determine the Shear Force at point B of the Beam shown.
If P = 26.5 and M = 9.73, Determine the Bending Moment at point B of the Beam shown.
Consider the beam in Figure P9.21 without theapplied load and support settlement. Compute the reac-tions and draw the shear and moment curves for the beamif support A rotates clockwise by 0.005 rad.
Analyze the beam: Draw the shear, moment, elastic curve, and axial diagram of the following, where P=55
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension TT in the restraining cable CD is 2.8 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take aa = 4.7 metres, and bb = 3.8 metres.
Compute the forces in members CD and JK, given that P = 3000 N and Q = 1000 N. (Hint: Use the section indicated by the dashed line.)
(a) Draw the shear and moment curves for theframe in Figure P5.40. Sketch the deflected shape.(b) Write the equations for shear and moment in columnAB. Take the origin at A. (c) Write the shear and momentequations for girder BC. Take the origin at joint B.
The cables in Figure P6.7 have been dimensioned so that a 3-kip tension force develops in each vertical strand when the main cables are tensioned. What value of jacking force T must be applied at supports B and C to tension the system?
Draw the shear and moment curves for each mem- ber of the rigid frame in Figure P5.41. Sketch the de- flected shape.
Determine the moment of this figure P1=35kN and P2=55kN