Calculate the answer, and present in scientific notation. (0.32)(14.50)(120)= (14.1)/(0.005)= (3.9)(6.05)(420)=
Q: The effect of temperature on the crystallization of a material is given below. Calculate the…
A: Given is Effect of temperature on the crystallization of the material To determine…
Q: Which procedure provides a method that may be used to apply Cstigliano's second theorem?
A: Castigliano’s theorem is used to identify the deformation in a body (by external load). For the…
Q: ᴀᴛ 101.325ᴋᴘᴀ ᴀɴᴅ 13ᴅᴇɢᴄ ꜱᴜʀʀᴏᴜɴᴅɪɴɢ, ᴀ ꜱɪɴɢʟᴇ ꜱᴛᴀɢᴇ, ꜱɪɴɢʟᴇ ᴀᴄᴛɪɴɢ ᴀɪʀ ᴄᴏᴍᴘʀᴇꜱꜱᴏʀ ʀᴜɴɴɪɴɢ ᴀᴛ…
A:
Q: Consider a ~30 ft metal pole in the ground, marking the road and snow level, at Sonora Pass, the…
A: Given data Length of pole = 30 ft = 9.144 m The metal pole can be either stainless steel or…
Q: 5 The following are the values of righting levers, in metres, at various angles of inclination for a…
A:
Q: ᴀ ᴘᴇʟᴛᴏɴ ᴡʜᴇᴇʟ ɪꜱ ᴛᴏ ʙᴇ ᴅᴇꜱɪɢɴᴇᴅ ᴛᴏ ʀᴜɴ ᴀᴛ 400ʀᴘᴍ ᴜɴᴅᴇʀ 150ᴍ ᴇꜰꜰᴇᴄᴛɪᴠᴇ ʜᴇᴀᴅ. ᴛʜᴇ ʀᴀᴛɪᴏ ᴏꜰ ᴛʜᴇ ɴᴏᴢᴢʟᴇ…
A: Given pelton wheel turbineN=400rpmH=150mdD=112η=84%=0.84speed ratio=0.55
Q: The costs to manufacture a part using methods A and B are estimated by CA= 10 + 0.8 P and CA= 10 +…
A: Given data The costs to manufacture a part using methods A are estimated by CA= 10 + 0.8 P The…
Q: Solve the five questions, then show your complete solutions! Given: FN = 52 MN = 100 SN = 75
A: As you mentioned 5 question so I am solving only that question Given that , P=4i+6j-8kF=6i-8j+k
Q: 9. In a factory, packages are moved from a room on the second floor to a station on the first floor…
A: COEFFICIENT OF FRICTION DEPENDS ON MATERIAL
Q: 26. The function s(d) 0.159 + 0.118logd relates the slope, s, of a beach to the average diameter, d,…
A: Slope of a line is defined as the ratio of the vertical rise to the horizontal run. Slope defines…
Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the maximum true…
A: Since it is given in the question, the relation between the true stress, true strain and the strain…
Q: Q. No 1. Explain the following graph and its meaning. What are the use of this graph. 6x 24 6x 37-…
A: The given curves are S-N curves which represent the magnitude of the completely reversed bending…
Q: Write the appropriate Nusselt value for the each set of conditions provided below. Write your answer…
A: NOTE: According to Bartleyby's policy we shall answer only three sub-parts so kindly repost other…
Q: Example-6 The four cylinder engine of a light truck owned by a utility company has been converted to…
A:
Q: Please show how to derive cagliotti function.
A: For parameterizing the experimental profile, Caglioti et alequation—originally .'s created for…
Q: The number of (large) inclusions in cast iron follows a Poisson distribution with a mean of 2.5 per…
A: Let X be the Poisson random variable with the parameter with the parameter k=2.5 inclusions per…
Q: Does the Macaulay function follows the same rules as for ordinary functions? Give an example?
A: Macaulay function all most follows the same rules as ordinary functions. Macaulay method used to…
Q: A pressure difference of 35 pa is available to force -10c air. through a circular sheet metalduct…
A:
Q: Suppose that you have a task of measuring the lengths of a bridge and a rivet and come up with 9969…
A:
Q: The angle of twist for a circular shaft subjected to a twisting moment is given bythe equation 0 =…
A: Given Data: The given relationship is θ=TLGJ The angle of twist θ is a dimensionless quantity. Its…
Q: y < -1Sx + 3000 y < 5x In the xy-plane, if a point with coordinates ( a, b) lies in the solution…
A: To find : The maximum possible value of b Given : The equations are y<-15x+3000 and y<5x. A…
Q: Do the graphs satisfy Hooke’s law? Why?
A: Consider the diagram shown below for the stress-strain relationship of copper. According to the…
Q: According to the Newton's cooling law, the temperature of any substance is directly related to the…
A: Newtons Law of cooling is the governing law in the heat transfer which state that heat is…
Q: 40 సుర 30 120 IS0 代、 20 Find 8 Normalize your final answer but you may keep "hat" variables on the…
A: Given : To find : θ2sTs
Q: 24.51 Given the data below, find the isothermal work done on the gas as it is compressed from 23 L…
A: Given:- V1=23 L V2=3 L V, L 3 8 13 18 23 P, atm 12.5 3.5 1.8 1.4 1.2 To find:- a) Work done…
Q: 9. In a factory, packages are moved from a room on the second floor to a station on the first floor…
A: Package are moved from Second floor to first floor using a ramp of metal A, when the ramp is…
Q: Given data : K=70 MPa Poisson ratio30.22 Find E
A: Given data : Bulk modulus=K Poisson ratio=μ Required : Modulus of elasticity
Q: Answer with True or False of the following question: 5. For a fluid at rest, the shear stress is…
A: 5 . For a fluid at rest, the shear stress is zero. True. When we apply shear stress on solid it…
Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…
A:
Q: Evaluate the integral by applying the following theorems and the power rule appropriately. Suppose…
A: Following concepts of integration are used in engineering mathematics of mechanical engineering.
Q: For turning operation, using the table below, find an opproximate value for the required speed of…
A: Given, Cutting speed, v=417 mm/s=417×10-3160 m/min=25.02 m/min The radius of the workpiece, R=0.01…
Q: According to our methods, if this part is subjected to 36,259 cycles at state 1, how many cycles of…
A: Given: A part subjected completely reverse load S1=37 ksi S2=43 ksi S=95.1N-0.0851 To determine: If…
Q: ompute the heat conducted in KW through a sheet of plate glass, k = 0.025 Cal/s-cm-ºC, which is 3.5…
A: Given Thermal conductivity, k = 0.025 Cal/s-cm-ºC = 10.46…
Q: An arrow is launched at v = 80 and 40 degrees. Find the maximum height, and the time it takes to…
A:
Q: Give me an explanation (Dodge and Metzner Correlation)with any mathematical example in finding (f)…
A: Correlations of friction factors are presented for the general case of purely viscous non-Newtonian…
Q: 1) In an orthogonal cutting operation, the cutting tool has a rake angle = 15°. The chip thickness…
A: give , rake angle α = 15 chip thickness before cut (t) - 0.2 mm chip thickness after cut (tc) -…
Q: -40.0° %3D 10 25.0 140.0° 25.0 10 20 30
A: we will discuss vector equivalent.
Q: Obtain the engine dimensions of a two cylinder, two stroke internal combustion engine from the…
A: Given data as per question Number of cylinders = 2 N = 3500rpm Piston speed =550 m/min Indicated…
Q: Whole Blood pH 7.35–7.40 Viscosity (37°C) 3.0 cP (at high shear rates) Specific gravity (25/4°C)…
A: The properties are given in the table.
Q: From the shear stress - shear strain diagram shown below, all the following are true except: Shear…
A: MUILTIPLE CHOICE :- a. Shear stress and shear strain are 430MPa and 1.72 rad at fracture:- True, we…
Q: A 4-cylinder engine with a bore to stroke ratio of 10 cm x 12 cm, and an individual clearance volume…
A:
Q: 17.28 For each of the metals listed in the following + table, compute the Pilling-Bedworth ratio.…
A:
Q: Which of the following parameters should not be selected as repeating variables in using Buckingham…
A: Answer: ◆ The parameters that should not be selected as repeating variables are: a. Both pressure…
Calculate the answer, and present in scientific notation.
(0.32)(14.50)(120)=
(14.1)/(0.005)=
(3.9)(6.05)(420)=
Step by step
Solved in 2 steps with 2 images
- A long steel rod is placed horizontally between two supports, one at each end. The rod bends a little in the center. Which property of this rod can be used to estimate how much the rod should bend at the center? 1. Its Shear Modulus 2. Its Young's Modulus 3. All of these Moduli can be used to compute how much it bends. 4. Its Bulk Modulus.5.2 Evaluate the Prandtl number from the following data: , .please show step-by-step calculations. answer choices are 0.34, 0.38, 0.42, 0.54, 0.85, 2.20, 2.58, 2.67, 3.11, 3.15, 1484, 1803, 2087, 2101, 2126
- The number of (large) inclusions in cast iron follows a Poisson distribution with a mean of 2.5 per cubic millimeter. Approximate the probability that more than 2440 inclusions occur in a cubic centimeter.A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration inDEVELOP THE FOLLOWING CASTIGLIANO THEOREM EXERCISE STEP BY STEP, PLACING THE MISSING STEPS
- Please solve part B please!! thank youu will rate your answer!ᴘᴀʀᴛ ᴀ.ᴀ ᴋɴᴜᴄᴋʟᴇ ᴊᴏɪɴᴛ ɪꜱ ᴛᴏ ʙᴇ ᴀxɪᴀʟʟʏ ʟᴏᴀᴅᴇᴅ ᴡɪᴛʜ ᴀ ᴛᴇɴꜱɪʟᴇ ʟᴏᴀᴅ ꜰ. ᴛʜᴇ ᴀꜱꜱᴇᴍʙʟʏ ᴏꜰ ᴘᴀʀᴛꜱ ᴀɴᴅ ᴛʜᴇɪʀ ᴠᴀʀɪᴀʙʟᴇᴅɪᴍᴇɴꜱɪᴏɴꜱ ᴀʀᴇ ꜱʜᴏᴡɴ ɪɴ ᴛʜᴇ ꜰɪɢᴜʀᴇ ʙᴇʟᴏᴡ. ᴡʀɪᴛᴇ ᴛʜᴇ ꜱᴛʀᴇꜱꜱ ᴇQᴜᴀᴛɪᴏɴ ᴀᴛ ᴇᴀᴄʜ ᴏꜰ ᴛʜᴇ ᴘᴏꜱꜱɪʙʟᴇ ʟᴏᴄᴀᴛɪᴏɴꜱ ᴏꜰ ꜰᴀɪʟᴜʀᴇ. ɪᴅᴇɴᴛɪꜰʏ ᴇᴀᴄʜ ꜱᴛʀᴇꜱꜱ ᴀɴᴅ ᴡʀɪᴛᴇ ɪᴛꜱ ᴇQᴜᴀᴛɪᴏɴ ɪɴ ᴛᴇʀᴍꜱ ᴏꜰ ᴛʜᴇ ʟᴏᴀᴅ ꜰ, ᴀɴᴅ ᴛʜᴇ ɢɪᴠᴇɴ ᴅɪᴍᴇɴꜱɪᴏɴꜱ ᴀ, ʙ, ᴄ, ᴅ, ᴋ, ᴍ ᴀɴᴅ ɴ. (ᴇxᴀᴍᴘʟᴇ: ᴛᴇɴꜱɪʟᴇ ꜱᴛʀᴇꜱꜱ ᴀᴛ ᴛʜᴇ ʀᴏᴅ ᴏꜰ ᴛʜᴇ ᴋɴᴜᴄᴋʟᴇ ᴊᴏɪɴᴛ: ꜱᴛ = 4ꜰ/Πᴅ2). ᴅᴏɴ’ᴛ ᴜꜱᴇ ᴠᴀʀɪᴀʙʟᴇꜱ ᴛʜᴀᴛ ᴀʀᴇ ɴᴏᴛ ᴅᴇꜰɪɴᴇᴅ ɪɴ ᴛʜᴇ ᴊᴏɪɴᴛ ᴅᴇꜱᴄʀɪʙᴇᴅ ʙᴇʟᴏᴡ. ꜱᴜᴘᴘᴏʀᴛ ᴇᴀᴄʜ ᴏꜰ ᴛʜᴇ ꜱᴛʀᴇꜱꜱ ᴇQᴜᴀᴛɪᴏɴꜱ ʙʏ ᴍᴇᴀɴꜱ ᴏꜰ ᴀɴ ɪꜱᴏᴍᴇᴛʀɪᴄ ᴅʀᴀᴡɪɴɢ ɪɴᴅɪᴄᴀᴛɪɴɢ ᴛʜᴇ ᴘᴀʀᴛ ᴀɴᴅ ɪᴛꜱ ᴅɪᴍᴇɴꜱɪᴏɴꜱ ᴛʜᴀᴛ ᴍɪɢʜᴛ ʜᴀᴠᴇ ꜰᴀɪʟᴇᴅ ᴅᴜᴇ ᴛᴏ ᴏᴠᴇʀꜱᴛʀᴇꜱꜱɪɴɢ. ꜰᴏʀ ᴛʜᴇ ʙᴇɴᴅɪɴɢ ꜱᴛʀᴇꜱꜱ ɪɴ ᴛʜᴇ ᴘɪɴ, ᴄᴏɴꜱɪᴅᴇʀ ᴛʜᴇ ʟᴏᴀᴅꜱ ᴛᴏ ʙᴇ ᴜɴɪꜰᴏʀᴍʟʏ ᴅɪꜱᴛʀɪʙᴜᴛᴇᴅ ᴀᴛ ᴛʜᴇ ᴄᴇɴᴛᴇʀ ᴏꜰ ᴛʜᴇ ᴄᴏᴛᴛᴇʀ ᴀɴᴅ ᴜɴɪꜰᴏʀᴍʟʏ ᴠᴀʀʏɪɴɢ ᴀᴛ ᴛʜᴇ ᴋɴᴜᴄᴋʟᴇ ᴇɴᴅ. ɴᴇɢʟᴇᴄᴛ ᴛʜᴇ ᴘʀᴇꜱᴇɴᴛ ᴏꜰ ᴛʜᴇ ꜰɪʟʟᴇᴛꜱ ɪɴ ᴄᴏɴꜱɪᴅᴇʀɪɴɢ ᴛʜᴇ ᴅɪᴍᴇɴꜱɪᴏɴꜱᴘᴀʀᴛ ʙ.ᴜꜱɪɴɢ ᴛʜᴇ ꜱᴛʀᴇꜱꜱ ᴇQᴜᴀᴛɪᴏɴꜱ ꜰᴏʀᴍᴇᴅ ɪɴ ᴘᴀʀᴛ ᴀ, ᴅᴇꜱɪɢɴ ᴛʜᴇ ᴊᴏɪɴᴛ ʙʏ ꜱᴘᴇᴄɪꜰʏɪɴɢ…For problem solving question, use precision of 0.0000 in your partial solutions and final answers. Input only the numerical value.Answer no. 17, given the number 16 below. The computed Q and time in 16 are, Q= 15 862.7953 kJ, t=143. 1397 mins. Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.
- Do the graphs satisfy Hooke’s law? Why?Suppose that you have a task of measuring the lengths of a bridge and a rivet and come up with 9969 and 9 cm, respectively. If the true values are 10,000 and 10 cm, respectively compute the true percent relative error for the bridge.Solve the five questions, then show your complete solutions! Given: FN = 52 MN = 100 SN = 75