According to the Newton's cooling law, the temperature of any substance is directly related to the distinction between the substance temperature and its environment (ambient) temperature dT =-k(T – T,)k(T-T) dt where T is the substance temperature (C) T is the time (minute) k is constant T, is environmental temperature A casting ladle of molten metal has 290 °C, By using Euler methodology, evaluate the temperature from t=0 to 35 min with a step size of 2 min. If, T, is 25°C and k is

According to the Newton's cooling law, the temperature of any substance is directly related to the distinction between the substance temperature and its environment (ambient) temperature dT =-k(T – T,)k(T-T) dt where T is the substance temperature (C) T is the time (minute) k is constant T, is environmental temperature A casting ladle of molten metal has 290 °C, By using Euler methodology, evaluate the temperature from t=0 to 35 min with a step size of 2 min. If, T, is 25°C and k is

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.26P

See similar textbooks

Similar questions

I need help calculating these values using the defined quantites: Fin using the given values (remember its units are m3/hour) the mass flux of water of the inlet stream E from the given values (make sure that it is in the correct units!) Vp= Volume of pond ** For this question, assume that Fin, Fout, and E do not change over time, and that Vp is at steady state Quantities: Pond geometry: r = 100 m; h = 8 m. cin = 0.5 g/m3 (constant over time); ci = 0.01 g/m3 Fin: The inlet stream can be approximated as rectangular in cross-section, with width w = 3 m and depth d = 1 m, and an average velocity uin = 0.5 m/s. E: The evaporation rate can be determined from the evaporative volume flux of 0.1 mm/hour.
A temperature scale of certain thermometer is given by the relationt = a ln p + bwhere a and b are constants and p is the thermometric property of the fluid in the thermometer. If at the ice point and steam point the thermometricproperties are found to be 1.5 and 7.5 respectively what will be the temperature corresponding to the thermometric property of 3.5 on Celsius scale.
The temperature of the ball as a function of time, T(t) in thebath may be estimated by this equation:T(t) = (Ti – T∞)e–t/τ + T ∞where t is the time in seconds in the bath; Ti is the initial ball temperature;T∞ is the oil temperature; and τ is the time constant in seconds thatdepends upon the material of the ball, the geometry of the ball, and oilproperties. Assume that the initial ball temperature = 800°C, the oil temperature = 40°C, and the time constant = 50 seconds. Using MATLAB, find the time at which the temperature of the ball bearing equals 600°C, 300°C, and 50°C
Unit weight of liquids Derive the formula used in determining the unit weight or density of a liquid using the displacement method. How is it different from the direct method? What are the practical applications of experiment?
Liquid biofuel (density= 789 kg/m3) is being pumped from a storage tank through a pipe with 1-inch innerdiameter (ID). The fuel is being pumped at a rate of 3.00 gallons per minute. In this process, what is thekinetic energy transport rate (Ėk) in units of horsepower (hp) and ft•lbf/sec.
Air is flowing naturally over a cylinder of D=(1) cm. Air has thermal conductivity 0.027W/mK, kinematic viscosity 1.9*10-5 m2/s, Rayleigh number 108, and Prandtl number0.72. Find the Nusselt number uses charts/table also if needed
Newton 's law of cooling describes the temperature T of a body cooling down to the surrounding temperature To. T and To are related through equation dT/dT =-k(T-To), where>0. Formulate an expression for T in terms of k and To
The rate of heat loss Qloss through a window or wall is athe function of the temperature difference between insideand outside ∆ T , the window surface area A , and the Rvalue of the window, which has units of (ft 2 .h . ° F)/ Btu.( a ) Using the Buckingham Pi Theorem, find an expressionfor the rate of heat loss as a function of the other threeparameters in the problem. ( b ) If the temperaturedifference ∆ T doubles, by what factor does the rate ofheat loss increase?
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.72 W/m deg C, Re=3840000, and Pr=0.7)?
A tank 3.5 m long and 2.5 m wide contains alcohol of relativedensity 0.82 to a depth of 3 m. A 50 mm diameter pipe leadsfrom the bottom of the tank. What will be the reading on agauge calibrated in Pa connected at a point (a) 150 mm abovethe bottom of the tank; (b) in the 50 mm diameter pipe, 2 mbelow the bottom of the tank; (c) at the upper end of a 25 mmdiameter pipe, connected to the 50 mm pipe 2 m below thebottom of the tank, sloping upwards at 30◦to the horizontalfor 1.2 m and then rising vertically for 600 mm? What is theload on the bottom of the tank?
A steel ball with the density of 6229 kg/m and the radius of 0,65 cm was dropped into the oil whose viscosity was to be measured as isseen in the figure. When the ball attains a constant velocity, the distance that the ball travelled was measured as 99 cm within the time interval of 4,7 sec. Before the experiment, the mass of the 100 ml-oil was measured as 2,1 gr. According to the data given above, find; a) the density of the oil (in kg/m ). (Please do not use any decimal digit.) b) the speed of the steel ball after the ball attains a constant velocity (in m/s). (Please use 4 decimal digits.) c) the dynamic viscosity of the oil (in Pa.s) (Please use 3 decimal digits.) d) the flow Reynolds number. (Please use 4 decimal digits.) Please solve this question step by step to reach correct answers. correct answers: a) 21 b) 0,2106 c) 2,715 d) 0,0212
A cylindrical tank shown below has a radius ? and a circular orifice at the bottom of radius ?. At time ? = 0 the liquid level in the tank is ho. (a) Use the Bernoulli equation to determine the relations between the orifice velocity ?o and the free surface velocity ?s (assume the surface velocity is not zero). (b) Use conservation of mass to determine the orifice velocity in terms of the free surface velocity. (c) Use the results in (a) and (b) to derive a differential equation for h(?). Note that ?s = − dh/dt. d) Separate variables and solve the equation for h(?) with the initial condition h(0) = ho (e) Determine how long it will take to empty the tank.