Calculate the corresponding depth of neutral axis from the extreme concrete compression fiber in a reinforced concrete beam 43*10 deep reinforced with bars 20-mm diameter enclosed with 10-mm diameter stirrups when the tensile steel strain is 0.008 and concrete compression strain is 0.003. F'c =25mpa

Calculate the corresponding depth of neutral axis from the extreme concrete compression fiber in a reinforced concrete beam 43*10 deep reinforced with bars 20-mm diameter enclosed with 10-mm diameter stirrups when the tensile steel strain is 0.008 and concrete compression strain is 0.003. F'c =25mpa

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Calculate the width of the concrete wall that is necessary to prevent the wall from sliding and the horizontal reaction acting on the system, Rx. The unit weight of the concrete is 23.6 kN/m^3 and the coefficient of friction between the base of the wall and the foundation soil is 0.42. Use 1.5 as the factor of safety against sliding. Will it also be safe from over turning?
Ignore the passive resistance in front of the wall and also the weight of soil on the face of the wall. (a) Check for stability of the wall with respect to sliding. (b) Check for overturning stability. (c) Does the eccentricity at the base exceed B/6? (d) What is the soil pressure beneath the toe and the heel? Sketch the pressure distribution. (e) Repeat (a) by taking into account the passive resistance in the face of the wall. (f) Comment on your results. Please solve with steps. Thanks
Determine the force P needed to pull the 50-kg roller over the smooth step. Take θ = 30°.
What is the minimum width for the base of a dam 30m high if upward pressure beneath the dam is assumed uniformly from full hydrostatic head at the heel to zero at the toes? Use the resultant of the reacting force cut the base at the downstream edge of the middle third of the base at O and weight of the concrete is 2.5w.
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
Problem 1) For the beam shown in the figure below has a width of 150 mm and height of 300 mm: B. ) Determine the flexural stress at a point 50 mm from the top of the beam's cross section and located at 2 meters from A. 112AN C 101Nm 25 m Fig. 6-29
The uniform 20-pound ladder is balanced in the rough floor with ms = 0.8 static friction coefficient and against the smooth wall at B. Calculate the horizontal force P that the man needs apply to the ladder to make it move.
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
For the dam retaining water as shown in the figure, the foundation soil is permeable; assume hydrostatic uplift varies from full hydrostatic head at the heel of the dam to zero at the toe. The unit weight of the concrete is 23.5 kN/m3. Find the factor of safety against sliding and overturning of the dam, and the pressure intensity on the base of the dam (at points A and B). Use coefficient of friction between the soil and dam be 0.45
Determine the force acting on one side of a concrete form 2.44݉ high and 1.22݉ wide that is used for pouring a basement wall. The specific weight of concrete is 23.5 kN / m3.
Determine the allowable shear stress if W= 33,813lb.