Calculate the current flowing through the 2.2k Q, 6.3M Q and 125 O resistor when supply voltage is (a) 6V (b) 10v (c) 15V (d) 21V Exercise 1. Current for each case with unit 2.2kn 6.3M2 1252 6V 10V 15V 21V Exercise 2: Calculate the current flowing through the resistor R1 (1k Q) V1 10 V R1 1ka Exercise 3: Implement the hardware for Exercise 2 and obtain the results.

Calculate the current flowing through the 2.2k Q, 6.3M Q and 125 O resistor when supply voltage is (a) 6V (b) 10v (c) 15V (d) 21V Exercise 1. Current for each case with unit 2.2kn 6.3M2 1252 6V 10V 15V 21V Exercise 2: Calculate the current flowing through the resistor R1 (1k Q) V1 10 V R1 1ka Exercise 3: Implement the hardware for Exercise 2 and obtain the results.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a design task, a wire of 2000 m requires to exhibit a voltage drop of 2.5 Vwhen 3.2 A of current passes though it. Based on the Table Q1 (b) below, inyour opinion, which of the wire is the most suitable for aviation when the fuelsaving is another factor to be considered as well.
a) In the circuit below, if resistor R1=12.83Ω, and resistor R2=97.66Ω, what is the equivalent resistance of this circuit in units of Ohms (Ω)? b) if the battery in the circuit below is 8.4V, resistor R1=57.31Ω, and resistor R2=65.71Ω, what is the magnitude of the current that passes through R1? Give your answer in units of milli-Amps (mA). c) if the battery in the circuit below is 8.4V, resistor R1=57.31Ω, and resistor R2=65.71Ω, what is the magnitude of the current that passes through R1? Give your answer in units of milli-Amps (mA).
a) The power, P, consumed by a resistor of resistance R, is given by P = E^2R Given that E = 20 V and R = 1000ꭥ, using partial derivatives, find the approximate change inpower if E is decreased by 0.5 V and R is increased by 50ꭥ.b) Check and compare your findings using standard electrical principles.
a)Determine a numerical value for each current and voltage (i1, v1, etc.) in the circuit shown below.b)verify that the principle of conservation of power in indeed true
An electric current flowing in a circuit (consisting of a battery ofV volts and a resistor of R ohms connected in series), satisfiesdIdt= −k (I −b)for some constants k and b with k > 0. Initially, I(0) = 0 and I(t)approaches a maximum level VRas t → ∞.(a) What is the value of b?b =(b) Find a formula for I(t) in terms of k, V, and R.I(t) =(c) What percent of its maximum value does I(t) reach at timet =7k?
An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of 5A is passed through the combination, it is found that the current in the aluminum wire is 3A. If the diameter of the aluminum wire is 1mm, determine the diameter of the copper wire. Assume the resistivity of copper to be 0.017µΩm and that of aluminum to be 0.028 µΩm. Major Topic 7 Factors that affect the resistance
Solve the following Numerical problems a. What is the Output Voltage of a battery that expends 7.2J of energy in moving 1C of charge? b. A 50-ohm load dissipates 200W of power. How much is the voltage and current across the load? c. If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load? d. If total resistance of a series circuit is 280-Ohm. If one of the resistance is 160-Ohm. What is the sum of other two resistances?
Determine the power dissipated the the variable resistor if RL is equal to 10 ohms. Also, find the current flowing in the 5-ohm resistor. Write your answer.
A circuit consisting of three ideal batteries with voltages E1, E2, E3 and three ideal resistors with resistances ?1,R1, ?2,R2, and ?3,R3, is shown in the figure. E1=28.0 V, E2=12.0 V, E3=27.0 V R1=4.90 kΩ, R2=18.0 kΩ,R3=4.00 kΩ Calculate the current IP through point P. Let the sign of the current correspond to its direction, with "up" being positive.
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
An automotive battery is rated at 120 A-h. Thismeans that under certain test conditions it can output1 A at 12 V for 120 h (under other test conditions, thebattery may have other ratings).a. How much total energy is stored in the battery?b. If the headlights are left on overnight (8 h), howmuch energy will still be stored in the battery in themorning? (Assume a 150-W total power rating forboth headlights together.)
1. In a circuit that contains only resistors in series, the current is the same throughout the circuit (remember that current is conserved!). The amount of current in the circuit is determined by the potential difference (or em f) of the battery and the equivalent resistance, Req, of the circuit. We can therefore write Ohm's Law as DeltaV = IReq. Assume the batteries supply a potential difference of DeltaV = 3.0 V, and use the currents measured in circuits 3a, 3b, and 3c to determine the equivalent resistance in each circuit. Please show the calculation of each. R1 = 150 ohm, R2 = 230 ohm R3 = 270 ohms (don't believe question should need these but providing anyways) Current MeasuredCurrent through R1 in 3a (Only resistor 1) Ir1= 0.01 amp Current through R1 in 3b (Resistor 1 and 2) Ir1= 0.0032 amp Current through R1 in 3c (Resistor 1, 2 and 3) Ir1 = 0.002 amp