For the problem below you are requested to calculate the factor of safety against heave, on the downstream sideof the sheet pile structure. REfere to the image below for the details of the design. H1 =thickness of the permeable layer is 12m, and the design depth of sheet plie D = 4.5m, (ysat = 17KN/m3).7m, H2 3m, the%3DSheet pileWaler level-Water levelImpervious layerSave All Ak Sene and Submit to saue and submit. Cik Saue AAszestesauealascars

Answered: Image /qna-images/answer/90d4e1f7-927b-4f93-a1a7-a7a88ea6840a.jpg

Answered: calculate the factor of safety against…

Engineering

Civil Engineering

calculate the factor of safety against heave,

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.10P

See similar textbooks

Similar questions

Design the anchored sheet pile wall supporting a loose sand fill as shown in the following Figure. GWT is at the same height on both sides, and assume yw=10kN/m³. Based on the log spiral solutions, the Ka for the loose sand is 0.3 while the K₂ and Kp for the dense sand are 0.2 and 13.125, respectively. Using the fixed earth support method, do the following: a) For a factor of safety of 2 on the passive resistance, determine the requirea depth of penetration depth, D. (initial trial with D'=1.5m) b) Determine the bending moment and the anchor load. c) Select a sheet pile section from the Table 9.1 (E-210x10³ MN/m² and fa-210 MN/m²) D O 7.0m. Yt = 16.5 kN/m³ $' = 30° Z Loose sand fill: Yt 19.5 kN/m3 $' = 30° Dense sand: Yt = 21 kN/m³ $' = 40° q=10 1.5m. 0.5m. kN/m²
A cantilever wall is to be installed in a granular material which has a unit weight of 122 pcf, a friction angle of 35 degrees. The height of the wall (H) is 29 ft and the ratio between the top of the wall the water to the wall height (a) is 0.25. The ratio of the pile soil friction angle to the soil friction angle (8/q) is -0.7. Using the Caquot and Kerisel lateral earth pressure coefficients and the chart solution in the "Steel Piling Design Manual" (USS, July 1984), what is the required sheetpile section in in^3? Use USS Mariner steel.
It is proposed to drive a cantilever sheet pile to a depth of h + d into dry granular soil to support excavation to a depth h. It is proposed to incorporate the safety factor by (a) increasing the computed depth of penetration do by 30% and (b) providing a safety factor of 1.75 on the passive resistance. Plot d/h against the friction angle for both cases (a) and (b) where d is the final depth of penetration below the excavation line.
A 50 cm square precast pile is driven by 9 m into a sandy soil. The standard penetration test results, prformed on this ground, are given in the table below: Depth below ground surface (m) SPT (Nss) 1.5 3.0 4.5 4 6 6.0 12 12 20 24 35 39 If the skin resistance is equal to {T, = 2 x (average Nss along the pile shaft)) kPa. Compute the factor of safety available, if 1100 kN of compressive load is applied on this pile. 7.5 9.0 10.5 12.0
In-situ stresses-Seepage condition ground level sheet Example: For the sheet pile which T is buried in sandy soil ,shown in 2.0m the figure below, find the total piling. water level and effective vertical stress at Points 0, 6, and 12?. 4.0m Note: Assume reasonable values for saturated and dry unit weight equipotential datum oollege Of I of the soil 3.0m flow line 3.0m Soil Mechanics : Lecture 2
Based on Meyerhof’s (1956) suggestion, do you think a mechanical or electrical cone penetration resistance (??) can be used to be the pile point ultimate bearing capacity (??)? C. Yes D. No
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A concrete pile 16 in. 16 in. in cross section is shown in Figure P12.13. Calculate the ultimate skin friction resistance by using the a. method [use Eq. (12.61) and Table 12.11] b. method c. method Use R=20 for all clays, which are normally consolidated.
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, ơ'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225KN/m? At 12m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 300KN/m? 7m 5m Clay 3 10m Unit weight = 18KN/m Friction angle = 0 degree 2 Cohesion = 100KN/m Figure 1: Pile system
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C, = 0.09, ơ'o = 150KN/m? At 10m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 225KN/m? At 12m, e, = 0.55, Cc = 0.32, C, = 0.09, oo = 300KN/m? 7m 5m Clay 10m Unit weight = 18kN/m Friction angle = 0 degree Cohesion = 100KN/m
In-situ stresses - Seepage condition ground level Example: For the sheet pile which is buried in sandy soil ,shown in the figure below, find the total and effective vertical stress at Points 0, 6, sheet piling. 2.0m water level 4.0m and 12?. Note: Assume reasonable values for equipotential datum saturated and dry unit weight of the soil 3.0 m 10 flow line 3.0m Soil Mechanics II: Lecture 2 8